參數資料
型號: ST16C654CJ68
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
中文描述: 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 12/51頁
文件大?。?/td> 968K
代理商: ST16C654CJ68
ST16C654/654D
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
REV. 5.0.0
12
2.7
The 654 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. For programming details, see
“Section
2.8, Programmable Baud Rate Generator” on page 12
F
IGURE
5. T
YPICAL
OSCILLATOR
CONNECTIONS
Crystal Oscillator or External Clock Input
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins. Typical oscillator connections are shown
in
Figure 5
. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal baud rate
generator for standard or custom rates. For further reading on oscillator circuit please see application note
DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
Each UART has its own Baud Rate Generator (BRG) with a prescaler. The prescaler is controlled by a software
bit in the MCR register. The MCR register bit-7 sets the prescaler to divide the input crystal or external clock by
1 or 4. The clock output of the prescaler goes to the BRG. The BRG further divides this clock by a
programmable divisor between 1 and (2
16
-1) to obtain a 16X sampling rate clock of the serial data rate. The
sampling rate clock is used by the transmitter for data bit shifting and receiver for data sampling.
T
ABLE
5: TXRDY#
AND
RXRDY# O
UTPUTS
IN
FIFO
AND
DMA M
ODE
FOR
C
HANNELS
A-D
P
INS
FCR
BIT
-0=0
(FIFO D
ISABLED
)
FCR B
IT
-0=1 (FIFO E
NABLED
)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
RXRDY#
0 = 1 byte
1 = no data
0 = at least 1 byte in FIFO
1 = FIFO empty
1 to 0 transition when FIFO reaches the trigger
level, or timeout occurs.
0 to 1 transition when FIFO empties.
TXRDY#
0 = THR empty
1 = byte in THR
0 = FIFO empty
1 = at least 1 byte in FIFO
0 = FIFO has at least 1 empty location.
1 = FIFO is full.
C1
22-47pF
C2
22-47pF
14.7456
MHz
XTAL1
XTAL2
R=300K to 400K
相關PDF資料
PDF描述
ST16C654CQ100 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
ST16C654 Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:600mA; Output Voltage:5V; Current Rating:30.05A; Leaded Process Compatible:No; Output Voltage Max:5V
ST16C654CQ64 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
ST16C654D Voltage Regulator IC; Package/Case:8-MSOP; Output Current:300mA; Output Voltage:3.3V; Supply Voltage Max:6V; Current Rating:300mA; Leaded Process Compatible:No; Output Current Max:300mA; Output Voltage Max:3.3V RoHS Compliant: No
ST16C654DIQ64 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
相關代理商/技術參數
參數描述
ST16C654CJ68-F 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C654CJ68-F DRY PACKED 制造商:EXAR 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 68-Pin PLCC
ST16C654CJ68TR 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C654CJ68TR-F 功能描述:UART 接口集成電路 QUAD UARTW/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C654CQ100 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: