參數資料
型號： SI5100-H-BL
廠商： Silicon Laboratories Inc
文件頁數： 6/40頁
文件大?。?/td> 0K
描述： IC TXRX SONET/SDH LP HS 195-PBGA
標準包裝： 119
系列： SiPHY™
類型： 收發器
驅動器/接收器數： 1/1
規程： SONET/SDH
電源電壓： 1.71 V ~ 1.89 V
安裝類型： 表面貼裝
封裝/外殼： 195-LBGA
供應商設備封裝： 195-BGA（15x15）
包裝： 托盤
Si5100
14
Rev. 1.5
4. Functional Description
The Si5100 transceiver is a low-power fully-integrated
serializer/deserializer that provides significant margin to
all
SONET/SDH
jitter
specifications.
The
device
operates from 2.41–2.7 Gbps making it suitable for OC-
48/STM-16
applications
and
OC-48/STM-16
applications that use 255/238 or 255/237 forward error
correction
(FEC)
coding.
The
low-speed
receive/transmit interface uses a low-power parallel
LVDS interface compatible with LVPECL.
5. Receiver
The receiver within the Si5100 includes a precision
limiting
amplifier,
a
jitter-tolerant
clock
and
data
recovery
unit
(CDR),
and
a
1:16
demultiplexer.
Programmable data slicing level and sampling phase
adjustment are provided to support bit-error-rate (BER)
optimization for long-haul applications.
5.1. Receiver Differential Input Circuitry
The receiver serial input provides proper termination
and biasing through two resistor dividers internal to the
device. The active circuitry has high-impedance inputs
and provides sufficient gain for the clock and data
recovery unit to recover the serial data. The input bias
levels are optimized for jitter tolerance and input
sensitivity and are typically not dc compatible with
standard I/Os; simply ac couple the data lines as shown
5.2. Limiting Amplifier
The Si5100 incorporates a limiting amplifier with
sufficient
gain
to
directly
accept
the
output
of
transimpedance amplifiers.
The limiting amplifier provides sufficient gain to fully
saturate with input signals that are greater than 30 mV
peak-to-peak differential. In addition, input signals up to
2 V
peak-to-peak
differential
do
not
cause
any
performance degradation.
5.2.1. Receiver Signal Amplitude Monitoring
The Si5100 limiting amplifier includes circuitry that
monitors the amplitude of the receiver differential input
signal (RXDIN). The RXAMPMON output provides an
analog output signal that is proportional to the input
signal amplitude. The signal is enabled when slice
mode is asserted. The voltage on the RXAMPMON
output is nominally equal to one-half of the differential
peak-to-peak signal amplitude of RXDIN as shown in
Equation 1
The receiver signal amplitude monitoring circuit is also
used in the generation of the loss-of-signal alarm (LOS).
5.2.2. Loss-of-Signal Alarm (LOS)
The Si5100 can be configured to activate a loss-of-
signal alarm output (LOS) when the RXDIN input
amplitude drops below a programmable threshold level.
An appropriate level of hysteresis prevents unnecessary
switching on LOS.
The LOS threshold level is set by applying a dc voltage
to the LOSLVL input. The mapping of the voltage on the
LOSLVL pin to the LOS threshold level depends on the
state of the SLICEMODE input. (The SLICEMODE input
is used to select either absolute slice mode or
proportional slice mode operation.)
The
LOSLVL
mapping
for
absolute
slice
mode
(SLICEMODE = 0) is given in Figure 4. The linear
region of the assert can be approximated by the
following equation:
Equation 2
where VLOS is the differential PK-PK LOS threshold
referred to the RXDIN input, and VLOSLVL is the voltage
applied to the LOSLVL pin.
The linear region of the de-assert curve can be
approximated by the following equation:
Equation 3
The LOSLVL mapping for proportional slice mode
(SLICEMODE = 1) is given in Figure 6 on page 17. The
linear region of the assert can be approximated by the
following equation:
Equation 4
where VLOS is the differential pk–pk LOS threshold
referred to the RXDIN input, and VLOSLVL is the voltage
applied to the LOSLVL pin.
The linear region of the de-assert curve can be
approximated by the following equation:
Equation 5
The LOS detection circuitry is disabled by tieing the
LOSLVL input to VREF. This forces the LOS output
high.
V
RXAMPMON
V
RXDIN PP
.566
V
LOS
V
LOSLVL
.958
V
LOS
V
LOSLVL
.762
V
LOS
V
LOSLVL
.61
V
LOS
V
LOSLVL
.72
相關PDF資料
PDF描述
MS27484E8A98P CONN PLUG 3POS STRAIGHT W/PINS
MS27474P14B5P CONN RCPT 5POS JAM NUT W/PINS
SI5100-H-GL IC TXRX SONET/SDH LP HS 195PBGA
IDT72V3650L7-5BB IC FIFO SS 2048X36 7-5NS 144BGA
MS27513E22F21PB CONN RCPT 21POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
Si5100-H-GL 功能描述:電信線路管理 IC OC-48 STM-16 SONET SDH Trnscvr 1:16 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI-51010-F 制造商:Bel Fuse 功能描述:- Trays
SI-51011-F 制造商:BEL 制造商全稱:Bel Fuse Inc. 功能描述:SI-51011-F
SI-51012-F 制造商:BEL 制造商全稱:Bel Fuse Inc. 功能描述:SI-51012-F
SI-51013-F 制造商:Bel Fuse 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*