- 您現在的位置：買賣IC網 > PDF目錄2016 > SI3019-F-GM (Silicon Laboratories Inc)IC VOICE GLOBAL DAA PROGR 20QFN PDF資料下載
參數資料
| 型號： | SI3019-F-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 48/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VOICE GLOBAL DAA PROGR 20QFN |
| 標準包裝： | 490 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Si3050 + Si3011/18/19
26
Rev. 1.5
5.6. Calibration
The Si3050 initiates two auto-calibrations by default
when the device goes off-hook or experiences a loss of
line power. A 17 ms resistor calibration is performed to
allow circuitry internal to the DAA to adjust to the exact
line conditions present at the time of going off-hook.
This resistor calibration can be disabled by setting the
RCALD
bit
(Register 25, bit 5).
A
256 ms
ADC
calibration is also performed to remove offsets that
might be present in the on-chip A/D converter, which
could affect the A/D dynamic range.
The ADC
auto-calibration is initiated after the DAA dc termination
stabilizes and the resistor calibration completes. Due to
the large variation in line conditions and line card
behavior presented to the DAA, it might be beneficial to
use manual ADC calibration instead of auto-calibration.
Manual ADC calibration should be executed as close as
possible to 256 ms before valid transmit/receive data is
expected.
The following steps should be taken to implement
manual ADC calibration:
1. The CALD bit (auto-calibration disable—Register 17)
must be set to 1.
2. The MCAL bit (manual calibration) must be toggled
to one and then 0 to begin and complete the
calibration.
3. The calibration is completed in 256 ms.
5.7. In-Circuit Testing
The Si3050’s advanced design provides the designer
with
an
increased
ability
to
determine
system
functionality during production line tests and support for
end-user
diagnostics.
Six
loopback
modes
allow
increased coverage of system components. For four of
the test modes, a line-side power source is needed.
While a standard phone line can be used, the test circuit
in Figure 1 on page 6 is adequate. In addition, an
off-hook sequence must be performed to connect the
power source to the line-side device.
For the start-up loopback test mode, no line-side power
is necessary, and no off-hook sequence is required. The
start-up test mode is enabled by default. When the PDL
bit (Register 6, bit 4) is set (the default case), the line
side is in a powerdown mode, and the system-side is in
a digital loopback mode. In this mode, data received on
DRX
passes
through
the
internal
filters
and
is
transmitted on DTX. This path introduces approximately
0.9 dB of attenuation on the DRX signal received. The
group delay of both transmit and receive filters exists
between DRX and DTX. Clearing the PDL bit disables
this mode, and the DTX data switches to the receive
data from the line side. When the PDL bit is cleared, the
FDT bit (Register 12, bit 6) becomes active to indicate
that successful communication between the line side
and
system
side
is
established.
This
provides
verification that the communications link is operational.
The digital data loop-back mode offers a way to input
data on the DRX pin and have the identical data output
on the DTX pin through bypassing the transmit and
receive filters. Setting the DDL bit (Register 10, bit 0)
enables this mode, which provides an easy way to verify
communication between the host processor/DSP and
the DAA. No line-side power or off-hook sequence is
required for this mode.
The remaining test modes require an off-hook sequence
to operate. The following sequence lists the off-hook
requirements:
1. Powerup or reset.
2. Allow the internal PLL to lock on PCLK and FSYNC.
3. Enable line-side by clearing PDL bit.
4. Issue an off-hook command.
5. Delay 402.75 ms for calibration to occur.
6. Set desired test mode.
The communications link digital loopback mode allows
the host processor to provide a digital input test pattern
on DRX and receive that digital test pattern back on
DTX. To enable this mode, set the IDL bit (Register 1,
bit 1). The communications link is tested in this mode.
The digital stream is delivered across the isolation
capacitors, C1 and C2, of the "2. Typical Application
Schematic" on page 17, to the line-side device and
returned across the same path. In this digital loopback
mode, the 0.9 dB attenuation and filter group delays
also exist.
The PCM analog loopback mode extends the signal
path of the analog loopback mode. In this mode, an
analog signal is driven from the line into the line-side
device. This analog signal is converted to digital data
and then passed across the communications link to the
system-side device. The data passes through the
receive filter, through the transmit filter, and is then
passed across the communications link and sent back
out onto the line as an analog signal. Set the PCML bit
(Register 33, bit 7) to enable this mode.
With the final testing mode, internal analog loopback,
the system can test the operation of the transmit and
receive paths on the line-side device and the external
components in the "2. Typical Application Schematic"
on page 17. The host provides a digital test waveform
on DRX. Data passes across the isolation barrier, is
transmitted to and received from the line, passes back
across the isolation barrier, and is presented to the host
on DTX. Clear the HBE bit (Register 2, bit 1) to enable
this mode.
相關PDF資料 |
PDF描述 |
|---|---|
| SI3063-F-FS | IC DAA ENH GLOB LINE-SIDE 16SOIC |
| SI3066-B-FS | IC DAA ENH FCC LINE-SIDE 8SOIC |
| SI3068-B-FS | IC FCC+ EMBEDDED DAA 8SOIC |
| SI3200-BS | IC LINEFEED INTRFC 100V 16SOIC |
| SI3211-KT | IC SLIC/CODEC PROG 1CH 38TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3019-F-GMR | 制造商:Silicon Laboratories Inc 功能描述:SI3050 ENHANCED GLOBAL VOICE DAA LINE-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC VOICE GLOBAL DAA PROGR 20QFN |
| Si3019-F-GS | 功能描述:電信線路管理 IC Si3050 Enhncd Global Voice DAA Line-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3019-F-GSR | 功能描述:電信線路管理 IC Enhanced Global Voice DAA Line-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Si3019-F-GT | 功能描述:電信線路管理 IC Si3050 Enhncd Global Voice DAA Line-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3019-F-GTR | 制造商:Silicon Laboratories Inc 功能描述:SI3050 ENHANCED GLOBAL VOICE DAA LINE-SIDE - LEAD-FREE - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。