- 您現在的位置：買賣IC網 > PDF目錄359756 > S29GL128P11FFIR10 (SPANSION LLC) 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology PDF資料下載
參數資料
| 型號： | S29GL128P11FFIR10 |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| 中文描述： | 128M X 1 FLASH 3V PROM, 110 ns, PBGA64 |
| 封裝： | 13 X 11 MM, 1 MM PITCH, LEAD FREE, FBGA-64 |
| 文件頁數： | 21/77頁 |
| 文件大小： | 2121K |
| 代理商： | S29GL128P11FFIR10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
November 8, 2007 S29GL-P_00_A7
S29GL-P MirrorBit
Flash Family
21
D a t a
S h e e t
( P r e l i m i n a r y )
7.6
Autoselect
The Autoselect mode provides
manufacturer ID, Device identification, and sector protection information
,
through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This
mode is primarily intended for programming equipment to automatically match a device to be programmed
with its corresponding programming algorithm (see
Table 7.3
). The Autoselect codes can also be accessed
in-system.
There are two methods to access autoselect codes. One uses the autoselect command, the other applies V
ID
on address pin A9.
When using programming equipment, the autoselect mode requires V
ID
(11.5 V to 12.5 V) on address pin A9.
Address pins must be as shown in
Table 7.2
.
To access Autoselect mode without using high voltage on A9, the host system must issue the Autoselect
command.
The Autoselect command sequence may be written to an address within a sector that is either in the read
or erase-suspend-read mode.
The Autoselect command may not be written while the device is actively programming or erasing.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
sector was previously in Erase Suspend).
It is recommended that A9 apply V
ID
after power-up sequence is completed. In addition, it is recommended
that A9 apply from V
ID
to V
IH
/V
IL
before power-down the V
CC
/V
IO
.
See
Table 12.1 on page 68
for command sequence details.
When verifying sector protection, the sector address must appear on the appropriate highest order address
bits (see
Table 7.4
to
Table 7.5
). The remaining address bits are don't care. When all necessary bits have
been set as required, the programming equipment may then read the corresponding identifier code on
DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128P11FFIR12 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P11FFIV10 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P11FFIV12 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P11TAI010 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P11TAI012 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128P11FFIS10 | 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Trays |
| S29GL128P11FFIS30 | 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Trays |
| S29GL128P11FFIS33 | 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Tape and Reel |
| S29GL128P11FFIS40 | 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Bulk |
| S29GL128P11FFIS43 | 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。