參數資料
型號： S1C63408F0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP128
封裝： PLASTIC, QFP-128
文件頁數： 11/151頁
文件大小： 1171K
代理商： S1C63408F0A0100
100
EPSON
S1C63406/408 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
4.11.10 Programming notes
(1) Be sure to initialize the serial interface mode in the transmit/receive disabled status (TXEN = RXEN =
"0").
(2) Do not perform double trigger (writing "1") to TXTRG (RXTRG) when the serial interface is in the
transmitting (receiving) operation.
(3) In the clock synchronous mode, since one clock line (SCLK) is shared for both transmitting and
receiving, transmitting and receiving cannot be performed simultaneously. (Half duplex only is
possible in clock synchronous mode.)
Consequently, be sure not to write "1" to RXTRG (TXTRG) when TXTRG (RXTRG) is "1".
(4) When a parity error or flaming error is generated during receiving in the asynchronous mode, the
receiving error interrupt factor flag ISER is set to "1" prior to the receive completion interrupt factor
flag ISRC for the time indicated in Table 4.11.10.1. Consequently, when an error is generated, you
should reset the receiving complete interrupt factor flag ISRC to "0" by providing a wait time in error
processing routines and similar routines.
When an overrun error is generated, the receiving complete interrupt factor flag ISRC is not set to "1"
and a receiving complete interrupt is not generated.
Table 4.11.10.1 Time difference between ISER and ISRC on error generation
Clock source
Time difference
fOSC3 / n
Programmable timer
1/2 cycles of fOSC3 / n
1 cycle of timer 1 underflow
(5) When the demultiplied signal of the OSC3 oscillation circuit is made the clock source, it is necessary
to turn the OSC3 oscillation ON, prior to using the serial interface.
A time interval of 5 msec, from the turning ON of the OSC3 oscillation circuit to until the oscillation
stabilizes, is necessary, due to the oscillation element that is used. Consequently, you should allow an
adequate waiting time after turning ON of the OSC3 oscillation, before starting transmitting/receiv-
ing of serial interface. (The oscillation start time will vary somewhat depending on the oscillator and
on the externally attached parts. Refer to the oscillation start time example indicated in Chapter 7,
"Electrical Chracteristics".)
At initial reset, the OSC3 oscillation circuit is set to OFF status.
(6) Be aware that the maximum clock frequency for the serial interface is limited to 2 MHz.
(7) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
相關PDF資料
PDF描述
S1C63406D0A0100 MICROCONTROLLER, UUC103
S1C63455F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128
S1C63455D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105
S1C63458F0A0100 MICROCONTROLLER, PQFP144
S1C63466D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140
相關代理商/技術參數
參數描述
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*