參數資料
型號: OX9162
廠商: Electronic Theatre Controls, Inc.
英文描述: Integrated Parallel Port/Local Bus and PCI interface
中文描述: 綜合并口/本地總線和PCI接口
文件頁數: 11/41頁
文件大?。?/td> 347K
代理商: OX9162
4.3
Data Sheet Revision 1.1 PRELIMINARY
Page 11
OX9162
OXFORD SEMICONDUCTOR LTD.
Accessing logical functions
Access to the local bus and parallel port is achieved via standard I/O and memory mapping, at addresses defined by the Base
Address Registers (BARs) in configuration space. The BARs are configured by the system to allocate blocks of I/O and memory
space to the logical function, according to the size required by the function. The addresses allocated can then be used to access
the function. The mapping of these BARs is shown in Table 4.
BAR
Local Bus
0
CS0 (I/O mapped)
1
CS1 (I/O mapped)
2
Local configuration registers (I/O mapped
3
Local configuration registers (memory mapped)
4
All CS (memory mapped
5
Function 0
Parallel Port
Parallel port base registers (I/O mapped)
Parallel port extended registers (I/O mapped)
Unused
Unused
Table 4: Base Address Register definition
4.3.1
When the local bus is enabled (Mode 1), the function
reserves two blocks of I/O space (BAR0 for chip select 0,
BAR1 for chip select 1) and a block of memory space
(BAR4 for chip selects 0 and 1). Each I/O block size is user
definable in the range of 4 to 256 bytes; the memory range
is fixed at 4K bytes.
I/O space
In order to minimise the usage of IO space, the block sizes
for BAR0 and BAR1 are user definable in the range of 4 to
256 bytes.
The 8-bit Local Bus has eight address lines (LBA[7:0])
which correspond to the maximum IO address space. If the
maximum allowable block size is allocated to the IO space
(i.e. 256 bytes), then as access in IO space is byte aligned,
LBA[7:0] equal PCI AD[7:0] respectively. When the user
selects an address range which is less than 256 bytes, the
corresponding upper address lines will be set to logic zero.
Memory Space:
The memory base address registers have an allocated
fixed size of 4K bytes in the address space. Since the
Local Bus has 8 address lines and the OX9162 only
implements DWORD aligned accesses in memory space,
the 256 bytes of addressable space per chip select is
expanded to 1K. Unlike an I/O access (where access to
BAR0, BAR1 determines chip-select decoding) for a
memory access the internal chip-select decoding logic
uses the field PCI AD[10] to decode into 2 chip-select
regions. When the Local Bus is accessed in memory
space, A[9:2] are asserted on LBA[7:0]. The chip-select
regions are defined below.
PCI access to 8-bit local bus
PCI Offset from BAR 1 in
Function1 (Memory space)
Lower Address
000h
400h
Local Bus
Chip-Select
Upper Limit
3FCh
7FCh
LBCS0# (LBDS0#)
LBCS1# (LBDS1#)
Table 5: PCI address map for local bus (memory)
Note: The description given for I/O and memory accesses
is for an Intel-type configuration for the Local Bus. For
Motorola-type configuration, the chip select pins are
redefined to data strobe pins. In this mode the Local Bus
offers up to 8 address lines and two data-strobe pins.
4.3.2
When the parallel port is enabled (Mode 0), access to the
port works via BAR definitions as usual with two I/O BARs
corresponding to the two sets of registers defined to
operate an IEEE1284 ECP/EPP and bi-directional Parallel
Port.
The user can change the I/O space block size of BAR0 or
BAR1 as for the local bus mode by over-writing the default
values using the serial EEPROM (see section 4.4).
Legacy parallel ports expect the upper register set to be
mapped 0x400 above the base block, therefore if the BARs
are fixed with this relationship, generic parallel port drivers
can be used to operate the device in all modes.
Example: BAR0 = 0x00000379 (8 bytes at address 0x378)
BAR1 = 0x00000779 (8 bytes at address 0x778)
If this relationship is not used, custom drivers will be
needed.
PCI access to parallel port
相關PDF資料
PDF描述
OXCB950 Integrated High Performance UART Cardbus / PCI interface
OXFW900 IEEE1394 to ATA/ATAPI Native Bridge
OXFW900-TQ-A IEEE1394 to ATA/ATAPI Native Bridge
OXFW911 IEEE1394 to ATA/ATAPI Native Bridge
OXFW911-TQ-A IEEE1394 to ATA/ATAPI Native Bridge
相關代理商/技術參數
參數描述
OX9240 制造商:RALTRON 制造商全稱:RALTRON 功能描述:OCXO
OX9241 制造商:RALTRON 制造商全稱:RALTRON 功能描述:OCXO
OX9340 制造商:RALTRON 制造商全稱:RALTRON 功能描述:OCXO
OX9341 制造商:RALTRON 制造商全稱:RALTRON 功能描述:OCXO
OX9440 制造商:RALTRON 制造商全稱:RALTRON 功能描述:OCXO