參數資料
型號： OX16CF950
廠商： Electronic Theatre Controls, Inc.
英文描述： LOW COST ASYNCHRONOUS 16 BIT CARD
中文描述： 低成本異步16位卡
文件頁數： 34/60頁
文件大?。?/td> 753K
代理商： OX16CF950
It is cleared on an ISR read of a level 5 interrupt.
Level 6:
CTS or RTS changed interrupt (ISR[5:0]=’100000’):
This interrupt is set whenever either of the CTS# or RTS#
pins changes state from low to high. It is cleared on an ISR
read of a level 6 interrupt.
6.6.4
Sleep Mode
For a channel to go into sleep mode, all of the following
conditions must be met:
Sleep mode enabled (IER[4]=1 in 650/950 modes, or
IER[5]=1 in 750 mode):
The transmitter is idle, i.e. the transmitter shift register
and FIFO are both empty.
SIN is high.
6.7
Modem Interface
Page 34
OXCF950 DATA SHEET V1.1
OXFORD SEMICONDUCTOR LTD.
The receiver is idle.
The receiver FIFO is empty (LSR[0]=0).
The UART is not in loopback mode (MCR[4]=0).
Changes on modem input lines have been
acknowledged (i.e. MSR[3:0]=0000).
No interrupts are pending.
A read of IER[4] (or IER[5] if a 1 was written to that bit
instead) shows whether the power-down request was
successful. The UART will fully retain its programmed state
whilst in power-down mode.
The channel will automatically exit power-down mode when
any of the conditions 1 to 7 becomes false. It may be
woken manually by clearing IER[4] (or IER[5] if the
alternate sleep mode is enabled).
Sleep mode operation is not available in IrDA mode.
6.7.1
MCR[0]: DTR
logic 0
Force DTR# output to inactive (high).
logic 1
Force DTR# output to active (low).
Note that DTR# can be used for automatic out-of-band flow
control when enabled using ACR[4:3] (see section 6.11.3).
MCR[1]: RTS
logic 0
Force RTS# output to inactive (high).
logic 1
Force RTS# output to active (low).
Note that RTS# can be used for automatic out-of-band flow
control when enabled using EFR[6] (see section 6.9.4).
MCR[2]: OUT1
logic 0
Force OUT1# output low when loopback mode
is disabled.
logic 1
Force OUT1# output high.
OUT1# is not bonded out in the OXCF950, but is internally
used for loopback testing
MCR[3]: OUT2
logic 0
Force OUT2# output low when loopback mode
is disabled.
logic 1
Force OUT2# output high.
OUT2# is not bonded out in the OXCF950, but is internally
used for loopback testing
MCR[4]: Loopback mode
logic 0
Normal operating mode.
Modem Control Register ‘MCR’
logic 1
Enable local loop-back mode (diagnostics).
In local loop-back mode, the transmitter output (SOUT) and
the modem outputs (DTR#, RTS#) are set in-active (high),
and the receiver inputs SIN, CTS#, DSR#, DCD#, and RI#
are all disabled. Internally the transmitter output is
connected to the receiver input and DTR#, RTS#, OUT1#
and OUT2# are connected to modem status inputs DSR#,
CTS#, RI# and DCD# respectively.
In this mode, the receiver and transmitter interrupts are
fully operational. The modem control interrupts are also
operational, but the interrupt sources are now the lower
four bits of the Modem Control Register instead of the four
modem status inputs. The interrupts are still controlled by
the IER.
MCR[5]: Enable XON-Any in Enhanced mode or enable
out-of-band flow control in non-Enhanced mode
650/950 modes (Enhanced mode):
logic 0
XON-Any is disabled.
logic 1
XON-Any is enabled.
In enhanced mode (EFR[4]=1), this bit enables the Xon-
Any operation. When Xon-Any is enabled, any received
data will be accepted as a valid XON (see in-band flow
control, section 6.9.3).
750 mode (Non-Enhanced mode):
logic 0
CTS/RTS flow control disabled.
logic 1
CTS/RTS flow control enabled.
相關PDF資料
PDF描述
OX2000A OCXO
OX2020A OCXO
OX2420A OCXO
OX4020A OCXO
OX4420A OCXO
相關代理商/技術參數
參數描述
OX16PCI952 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated High Performance Dual UARTs, Parallel Port and 5.0v PCI interface
OX16PCI952_05 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated High Performance Dual UARTs, Parallel Port and 5.0v PCI interface
OX16PCI952-TQAG 制造商:PLX Technology 功能描述: 制造商:Oxford Semiconductor 功能描述:IC PCI BRIDGE DUAL PORT UART SMD
OX16PCI952-TQC60-A 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated High Performance Dual UARTs, Parallel Port and 5.0v PCI interface
OX16PCI952-TQFP-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Integrated High Performance Dual UARTs, Parallel Port and 5.0v PCI interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*