- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6000DTBR2G (ON Semiconductor)IC INTERFACE SMART CARD 20TSSOP PDF資料下載
參數資料
| 型號： | NCN6000DTBR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 24/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 產品變化通告： | Product Obsolescence 01/Jul/2009 |
| 標準包裝： | 1 |
| 應用： | ATM 終端，氣泵，ISM |
| 接口： | 微控制器 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 剪切帶 (CT) |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6000DTBR2GOSCT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
30
Input Schmitt Triggers
All the Logic Input pins have builtin Schmitt trigger
circuits to prevent the NCN6000 against uncontrolled
operation. The typical dynamic characteristics of the related
pins are depicted in Figure 33.
The output signal is guaranteed to go High when the input
voltage is above 0.70*Vbat, and will go Low when the input
voltage is below 0.30*Vbat.
The CLOCK_IN pin has been design to provide a 40 MHz
bandwidth clock receiver input, capable to drive the internal
clock divider. This front end circuit yields a constant Duty
Cycle signal, according to the ISO specification, to the
external smart card, even when the NCN6000 division ratio
is 1:1.
Output
Vbat
ON
OFF
Vbat
0.70
*V
bat
Figure 33. Typical Schmitt Trigger Characteristic
Input
0.30
*V
bat
Interrupt Function
The NCN6000 flags the external microprocessor by pulling down the INT signal provided in pin 9. This signal is activated
by one of the here below referenced operations.
Table 6. Interrupt Functions
Pin Related
Clear Function
STATUS Pin 5
Card Insertion and
Extraction
11
Positive Going Chip Select, or logical
combination of Chip Select Low and
PWR_ON Positive Going
High = Card Presents
Low = No Card Inserted
DCDC Converter
Overloaded
15
Positive Going Chip Select, or logical
combination of Chip Select Low and
PWR_ON Positive Going
High = DCDC Operates Normally
Low = Output CRD_VCC Overloaded
Leaving the INT pin Low has no influence on the
NCN6000 internal behavior. It is up to the engineering to
decide when and how the interrupt will be cleared from this
pin. As described before, this can be achieved by either
providing a Chip Select positive transient, or by starting the
DCDC converter with the standard command PWR_ON =
H and CS =L.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | IC INTERFACE SMART CARD 20TSSOP |
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6001 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_0610 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001DTBEVB | 功能描述:界面開發工具 NCN6001 TSSOP EVAL BOARD RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。