- 您現在的位置：買賣IC網 > PDF目錄98045 > MTB40N10E (ON SEMICONDUCTOR) 40 A, 100 V, 0.04 ohm, N-CHANNEL, Si, POWER, MOSFET PDF資料下載
參數資料
| 型號： | MTB40N10E |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | JFETs |
| 英文描述： | 40 A, 100 V, 0.04 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 封裝： | D2PAK-3 |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 119K |
| 代理商： | MTB40N10E |
MTB40N10E
http://onsemi.com
9
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 18 shows a typical heating
profile for use when soldering a surface mount device to a
printed circuit board. This profile will vary among
soldering systems but it is a good starting point. Factors that
can affect the profile include the type of soldering system in
use, density and types of components on the board, type of
solder used, and the type of board or substrate material
being used. This profile shows temperature versus time.
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177–189
°C. When this type of furnace is used for solder
reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°C
150
°C
100
°C
5
°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
° TO 219°C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°C
150
°C
160
°C
170
°C
140
°C
Figure 18. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MTB40N10ET4 | 40 A, 100 V, 0.04 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTB50N06VLT4 | 42 A, 60 V, 0.032 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTB50N06VL | 42 A, 60 V, 0.032 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTB50P03HDLT4 | 50 A, 30 V, 0.03 ohm, P-CHANNEL, Si, POWER, MOSFET |
| MTB52N06VLT4 | 52 A, 60 V, 0.025 ohm, N-CHANNEL, Si, POWER, MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTB40N10ET4 | 制造商:ON Semiconductor 功能描述:Trans MOSFET N-CH 100V 40A 3-Pin(2+Tab) D2PAK T/R |
| MTB44P04J3 | 制造商:CYSTEKEC 制造商全稱:Cystech Electonics Corp. 功能描述:P-Channel Enhancement Mode Power MOSFET |
| MTB45A06Q8 | 制造商:CYSTEKEC 制造商全稱:Cystech Electonics Corp. 功能描述:Dual N-Channel Logic Level Enhancement Mode Power MOSFET |
| MTB4N40ET4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MTB4N50ET4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。