- 您現在的位置：買賣IC網 > PDF目錄45331 > MK50H27Q25 (STMICROELECTRONICS) 1 CHANNEL(S), 51M bps, SERIAL COMM CONTROLLER, PQCC52 PDF資料下載
參數資料
| 型號： | MK50H27Q25 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1 CHANNEL(S), 51M bps, SERIAL COMM CONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 11/58頁 |
| 文件大?。?/td> | 621K |
| 代理商： | MK50H27Q25 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
sion of SIOS can be resumed by issuing UPRIM 16 described above.
Valid only in Out Of Service phase when JSS7E=1 (CSR2).
07
PLOST
PROVIDER PRIMITIVE LOST is set by MK50H27 when a provider
primitive cannot be issued because the PAV bit is still set from the pre-
vious provider primitive. PLOST is cleared when PAV is cleared and
by a Bus RESET. Writing to this bit has no affect.
06
PAV
PROVIDER PRIMITIVE AVAILABLE is set by the MK50H27 when a
new provider primitive has been placed in PPRIM.
PPRIM is
READ/CLEAR ONLY and is set by the chip and cleared by writing a "1"
to the bit or by Bus RESET. Under normal operation the host should
clear the PAV bit after PPRIM is read.
05:00
PPRIM
PROVIDER PRIMITIVE is written by the MK50H27, in conjunction
with setting the PAV bit, to inform the user of link control
condi-
tions.
Valid Provider Primitives are as follows:
0
Init Confirmation: indicates that the initialization has completed.
1
In Service: indicates that alignment has completed successfully.
2
In Service Yellow: indicates alignment completed succesfully with CCITT
Yellow Book definitions for SINs & SIEs (SF = 9 & 10 respectively).
This primitive will occur only if enabled by RYEL=1 in Protocol Options.
3
Transmit Clock Watchdog Timer Expired: indicates that the watchdog
timer for TCLK has expired due to no transition on TCLK for more than
the number of SYSCLK cycles as selected by CSR4<15:14>.
4
Receive Clock Watchdog Timer Expired: indicates that the watchdog
timer for RCLK has expired due to no transition on RCLK for more than
the number of SYSCLK cycles as selected by CSR4<13:12>.
5
Received SU Timer timeout: indicates that no signal units have been
received within the previous 32xTP time (where TP is the poll timer).
This primitive is only issued if RSUTE=1 (CSR2<12>).
8
Alignment Out of Service: indicates that a transfer to Out of Service
phase has occured, due to an alignment failure.
Alignment will fail if
AERM is exceeded, timer T2 times out, or timer T3 times out.
9
LSSU Out of Service: indicates that a transfer to the Out of Service
phase has occured, due to a received LSSU.
10
T1 Out of Service: indicates that a transfer to the Out of Service
phase has occured, due to a timer T1 time out.
11
Transmit Out of Service: indicates that a transfer to the Out of
Service phase has occured, due to a transmit link failure. The trans-
mit link will fail if timers T6 or T7 time out.
‘
12
Receive Out of Service: indicates that a transfer to the Out of Service
phase has occured due to receive link failure. A receive link failure will
occur when more than 2 out of 3 signal units have a FIB or BSN error.
13
SUERM Out of Service: indicates that a transfer to the Out of Service
phase has occured, due to SUERM being exceeded.
16
Remote Processor Outage: indicates that a SIPO has been received
indicating that a remote processor outage condition has occured.
17
Remote Processor Outage Recovered: an FISU or an MSU has been
received since remote processor outage condition has been reported.
18
Received message BSNT: indicates that the MK50H27 has written the
BSNT to the Status Buffer as requested by UPRIM 12.
19
Retrieval complete: retrieval request and FSNC completed successfully.
The pointer to the retransmission buffer is available in STATUS buffer.
20
Remote Processor Busy: an SIB has been received indicating that
the remote node has entered into congestion.
21
Remote Processor Busy Recovered: the remote node has acknowledged
MK50H27
19/56
相關PDF資料 |
PDF描述 |
|---|---|
| MK50N512CLQ100 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| MK50X256CMC100 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA121 |
| MK50N512CMC100 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA121 |
| MK51DN512ZCLQ10 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| MK51DN256ZCMD10 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK50H27Q33B | 功能描述:射頻無線雜項 SS7 Controller 33MHz RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| MK50H27TQ25B | 制造商:STMicroelectronics 功能描述:SS7 HDLC CONTROL - Tape and Reel |
| MK50H27TQ33B | 功能描述:電信集成電路 SS7 Controller 33MHz RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| MK50H28 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MULTI LOGICAL LINK FRAME RELAY CONTROLLER |
| MK50H28DIP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MULTI LOGICAL LINK FRAME RELAY CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。