參數資料
型號： MAX16046
廠商： Maxim Integrated Products, Inc.
英文描述： 12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
中文描述： 12/8通道EEPROM可編程系統管理器，提供非易失故障寄存器
文件頁數： 56/68頁
文件大?。?/td> 570K
代理商： MAX16046
M
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
56
______________________________________________________________________________________
LOAD ADDRESS:
This is an extension to the standard
IEEE 1149.1 instruction set to support access to the
memory in the MAX16046/MAX16048. When the LOAD
ADDRESS instruction latches into the instruction regis-
ter, TDI connects to TDO through the 8-bit memory
address test data register during the shift-DR state.
READ DATA:
This is an extension to the standard IEEE
1149.1 instruction set to support access to the memory
in the MAX16046/MAX16048. When the READ instruc-
tion latches into the instruction register, TDI connects to
TDO through the 8-bit memory read test data register
during the shift-DR state.
WRITE DATA:
This is an extension to the standard
IEEE 1149.1 instruction set to support access to the
memory in the MAX16046/MAX16048. When the WRITE
instruction latches into the instruction register, TDI con-
nects to TDO through the 8-bit memory write test data
register during the shift-DR state.
REBOOT:
This is an extension to the standard IEEE
1149.1 instruction set to initiate a software controlled
reset to the MAX16046/MAX16048. When the REBOOT
instruction latches into the instruction register, the
MAX16046/MAX16048 resets and immediately begins
the boot-up sequence.
SAVE:
This is an extension to the standard IEEE 1149.1
instruction set that triggers a fault log. The current ADC
conversion results along with fault information are
saved to EEPROM depending on the configuration of
the Critical Fault Log Control register (r47h).
SETEXTRAM
: This is an extension to the standard
IEEE 1149.1 instruction set that allows access to the
extended page. Extended registers include ADC con-
version results, DACOUT enables, and GPIO input/out-
put data.
RSTEXTRAM:
This is an extension to the standard IEEE
1149.1 instruction set. Use RSTEXTRAM to return to the
default page and disable access to the extended page.
SETEEPADD:
This is an extension to the standard
IEEE 1149.1 instruction set that allows access to the
EEPROM page. Once the SETEEPADD command has
been sent, all addresses are recognized as EEPROM
addresses only.
RSTEEPADD:
This is an extension to the standard IEEE
1149.1 instruction set. Use RSTEEPADD to return to the
default page and disable access to the EEPROM.
Applications Information
Unprogrammed Device Behavior
When the EEPROM has not been programmed using
the JTAG or I
2
C interface, the default configuration of
the EN_OUT_ outputs is open-drain active-low. If it is
necessary to hold an EN_OUT_ high or low to prevent
premature startup of a power supply before the
EEPROM is programmed, connect a resistor to ground
or the supply voltage. Avoid connecting a resistor to
ground if the output is to be configured as open-drain
with a separate pullup resistor.
Device Behavior at Power-Up
When V
CC
is ramped from 0V, the
RESET
output is high
impedance until V
CC
reaches 1.4V, at which point it is
driven low. All other outputs are high impedance until
V
CC
reaches 2.85V, when the EEPROM contents are
copied into register memory, and after which the out-
puts assume their programmed states.
Margining Power Supplies
The MAX16046/MAX16048 can margin or shift the volt-
ages on external power supplies to facilitate prototyp-
ing or manufacturing tests. There are several different
ways to margin power supplies: One method feeds a
current into the feedback node of a DC-DC converter or
LDO, and another method feeds a current into the trim
input on a DC-DC module.
Feedback Method
See Figure 15 for the connections of the MAX16046/
MAX16048 to a power supply using the feedback node
method. The output voltage, V
OUT
, can be calculated
using the following formula:
where V
REF
is the internal reference voltage of the
power supply and V
DACOUT_
is the output voltage of
the MAX16046/MAX16048 DACOUT_ output.
Select R
1
and R
2
to obtain the desired output voltage
with no trim in effect (V
DACOUT_
= V
REF
). Set the DAC
range bits such that V
REF
falls approximately halfway
within the DACOUT_ output range (see the DAC
Outputs section). The resistor, R
3
, varies the amount of
control that the DACOUT_ voltage has on the output
voltage of the power supply. Large values of R
3
corre-
spond to a higher degree of resolution control over the
output voltage, and small values of R
3
correspond to a
lesser degree of resolution control.
V
V
1
R
R
R
R
R
R
V
OUT
REF
1
3
1
2
1
3
DACOUT_
=
+
+
相關PDF資料
PDF描述
MAX16050 Voltage Monitors/Sequencer Circuits with Reverse-Sequencing Capability
MAX1605ETT-T 30V Internal Switch LCD Bias Supply
MAX1605EUT-T 30V Internal Switch LCD Bias Supply
MAX1605 30V Internal Switch LCD Bias Supply
MAX160MJN ; External Depth:125mm; External Width:45mm; Length/Height, External:68mm; Power Rating:4kW RoHS Compliant: Yes
相關代理商/技術參數
參數描述
MAX16046ACB+ 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16046ACB+T 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16046ATN+ 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16046ATN+T 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16046ECB+ 功能描述:監控電路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*