- 您現在的位置：買賣IC網 > PDF目錄180218 > M48T129V-70CS1 (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO32 PDF資料下載
參數資料
| 型號： | M48T129V-70CS1 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO32 |
| 封裝： | 8 X 20 MM, PLASTIC, TSOP-32 |
| 文件頁數： | 19/22頁 |
| 文件大?。?/td> | 140K |
| 代理商： | M48T129V-70CS1 |
M48T129Y, M48T129V
6/22
CLOCK OPERATIONS
Reading the Clock
Updates to the TIMEKEEPER registers should be
halted before clock data is read to prevent reading
data in transition. Because the BiPORT TIME-
KEEPER cells in the RAM array are only data reg-
isters, and not the actual clock counters, updating
the registers can be halted without disturbing the
clock itself.
Updating is halted when a ’1’ is written to the
READ bit, D6 in the Control Register (1FFF8h). As
long as a ’1’ remains in that position, updating is
halted. After a halt is issued, the registers reflect
the count; that is, the day, date, and time that were
current at the moment the halt command was is-
sued. All of the TIMEKEEPER registers are updat-
ed simultaneously. A halt will not interrupt an
update in progress. Updating occurs 1 second af-
ter the READ bit is reset to a ’0’.
Setting the Clock
Bit D7 of the Control Register (1FFF8h) is the
WRITE bit. Setting the WRITE bit to a ’1’, like the
READ bit, halts updates to the TIMEKEEPER reg-
isters. The user can then load them with the cor-
rect day, date, and time data in 24 hour BCD
format (see Table 11).
Resetting the WRITE bit to a ’0’ then transfers the
values of all time registers (1FFFFh-1FFF9h,
1FFF1h) to the actual TIMEKEEPER counters and
allows normal operation to resume. After the
WRITE bit is reset, the next clock update will occur
approximately one second later.
Note: Upon power-up following a power failure,
both the WRITE bit and the READ bit will be reset
to ’0’.
Stopping and Starting the Oscillator
The oscillator may be stopped at any time. If the
device is going to spend a significant amount of
time on the shelf, the oscillator can be turned off to
minimize current drain on the battery. The STOP
bit is located at Bit D7 within 1FFF9h. Setting it to
a ’1’ stops the oscillator. When reset to a ’0’, the
M48T129Y/V oscillator starts within one second.
Note: It is not necessary to set the WRITE bit
when setting or resetting the FREQUENCY TEST
bit (FT) or the STOP bit (ST).
SETTING ALARM CLOCK
Registers 1FFF6h-1FFF2h contain the alarm set-
tings. The alarm can be configured to go off at a
prescribed time on a specific month, date, hour,
minute, or second or repeat every month, day,
hour, minute, or second. It can also be pro-
grammed to go off while the M48T129Y/V is in the
battery back-up to serve as a system wake-up call.
Bits RPT5-RPT1 put the alarm in the repeat mode
of operation. Table 12 shows the possible config-
urations. Codes not listed in the table default to the
once per second mode to quickly alert the user of
an incorrect alarm setting.
Note: User must transition address (or toggle Chip
Enable) to see Flag Bit change.
When the clock information matches the alarm
clock settings based on the match criteria defined
by RPT5-RPT1, the AF (Alarm Flag) is set. If AFE
(Alarm Flag Enable) is also set, the alarm condi-
tion activates the IRQ/FT pin. To disable alarm,
write ’0’ to the Alarm Date register and RPT1-4.
The IRQ/FT output is cleared by a read to the
Flags register as shown in Figure 12. A subse-
quent read of the Flags register will reset the
Alarm Flag (D6; Register 1FFF0h).
The IRQ/FT pin can also be activated in the bat-
tery back-up mode. The IRQ/FT will go low if an
alarm occurs and both ABE (Alarm in Battery
Back-up Mode Enable) and AFE are set. The ABE
and AFE bits are reset during power-up, therefore
an alarm generated during power-up will only set
AF. The user can read the Flag Register at system
boot-up to determine if an alarm was generated
while the M48T129Y/V was in the deselect mode
during power-up. Figure 13 illustrates the back-up
mode alarm timing.
相關PDF資料 |
PDF描述 |
|---|---|
| M48T8-150PC1 | REAL TIME CLOCK, PDIP28 |
| M48Z02-150PC6 | 2K X 8 NON-VOLATILE SRAM MODULE, 150 ns, PDIP24 |
| M49142/05-0016 | PANEL MOUNT, CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, CRIMP, RECEPTACLE |
| M49142/05-0116 | PANEL MOUNT, CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, CRIMP, RECEPTACLE |
| M49142/05-0216 | PANEL MOUNT, CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, CRIMP, RECEPTACLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M48T129V-70PM1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.3V, 1 Mbit (128 Kbit x 8) TIMEKEEPER SRAM |
| M48T129V-85CS1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.3V-5V 1 Mbit 128Kb x8 TIMEKEEPER SRAM |
| M48T129V-85PM1 | 功能描述:實時時鐘 1M (128Kx8) 85ns RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M48T129VPM | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.3V-5V 1 Mbit 128Kb x8 TIMEKEEPER SRAM |
| M48T129VSH | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.3V-5V 1 Mbit 128Kb x8 TIMEKEEPER SRAM |
發布緊急采購，3分鐘左右您將得到回復。