參數資料
型號： M34554MC-XXXFP
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64
文件頁數： 59/138頁
文件大?。?/td> 1082K
代理商： M34554MC-XXXFP
Rev.3.00
Aug 06, 2004
page 27 of 136
REJ03B0043-0300Z
4554 Group
(1) External 0 interrupt request flag (EXF0)
External 0 interrupt request flag (EXF0) is set to “1” when a valid
waveform is input to D8/INT0 pin.
The valid waveforms causing the interrupt must be retained at their
level for 4 clock cycles or more of the system clock (Refer to Figure
16).
The state of EXF0 flag can be examined with the skip instruction
(SNZ0). Use the interrupt control register V1 to select the interrupt
or the skip instruction. The EXF0 flag is cleared to “0” when an in-
terrupt occurs or when the next instruction is skipped with the skip
instruction.
External 0 interrupt activated condition
External 0 interrupt activated condition is satisfied when a valid
waveform is input to D8/INT0 pin.
The valid waveform can be selected from rising waveform, falling
waveform or both rising and falling waveforms. An example of
how to use the external 0 interrupt is as follows.
Set the bit 3 of register I1 to “1” for the INT0 pin to be in the in-
put enabled state.
Select the valid waveform with the bits 1 and 2 of register I1.
Clear the EXF0 flag to “0” with the SNZ0 instruction.
Set the NOP instruction for the case when a skip is performed
with the SNZ0 instruction.
Set both the external 0 interrupt enable bit (V10) and the INTE
flag to “1.”
The external 0 interrupt is now enabled. Now when a valid wave-
external 0 interrupt occurs.
(2) External 1 interrupt request flag (EXF1)
External 1 interrupt request flag (EXF1) is set to “1” when a valid
waveform is input to D9/INT1 pin.
The valid waveforms causing the interrupt must be retained at their
level for 4 clock cycles or more of the system clock (Refer to Figure
16).
The state of EXF1 flag can be examined with the skip instruction
(SNZ1). Use the interrupt control register V1 to select the interrupt
or the skip instruction. The EXF1 flag is cleared to “0” when an in-
terrupt occurs or when the next instruction is skipped with the skip
instruction.
External 1 interrupt activated condition
External 1 interrupt activated condition is satisfied when a valid
waveform is input to D9/INT1 pin.
The valid waveform can be selected from rising waveform, falling
waveform or both rising and falling waveforms. An example of
how to use the external 1 interrupt is as follows.
Set the bit 3 of register I2 to “1” for the INT1 pin to be in the in-
put enabled state.
Select the valid waveform with the bits 1 and 2 of register I2.
Clear the EXF1 flag to “0” with the SNZ1 instruction.
Set the NOP instruction for the case when a skip is performed
with the SNZ1 instruction.
Set both the external 1 interrupt enable bit (V11) and the INTE
flag to “1.”
The external 1 interrupt is now enabled. Now when a valid wave-
form is input to the D9/INT1 pin, the EXF1 flag is set to “1” and the
external 1 interrupt occurs.
相關PDF資料
PDF描述
M34554EDFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP64
M3455AG8-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AGCFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AGC-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AG8FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
相關代理商/技術參數
參數描述
M34556G8FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34556G8HFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34556M4H-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34556M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34556M8H-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*