參數資料
型號: M34507M4-XXXFP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, MICROCONTROLLER, PDSO24
封裝: 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24
文件頁數: 25/117頁
文件大?。?/td> 937K
代理商: M34507M4-XXXFP
4507 Group
Rev.3.01
2005.02.04
page 13 of 111
REJ03B0107-0301
(5) Stack registers (SKS) and stack pointer (SP)
Stack registers (SKs) are used to temporarily store the contents of
program counter (PC) just before branching until returning to the
original routine when;
branching to an interrupt service routine (referred to as an inter-
rupt service routine),
performing a subroutine call, or
executing the table reference instruction (TABP p).
Stack registers (SKs) are eight identical registers, so that subrou-
tines can be nested up to 8 levels. However, one of stack registers
is used respectively when using an interrupt service routine and
when executing a table reference instruction. Accordingly, be care-
ful not to over the stack when performing these operations
together. The contents of registers SKs are destroyed when 8 lev-
els are exceeded.
The register SK nesting level is pointed automatically by 3-bit
stack pointer (SP). The contents of the stack pointer (SP) can be
transferred to register A with the TASP instruction.
Figure 5 shows the stack registers (SKs) structure.
Figure 6 shows the example of operation at subroutine call.
(6) Interrupt stack register (SDP)
Interrupt stack register (SDP) is a 1-stage register. When an inter-
rupt occurs, this register (SDP) is used to temporarily store the
contents of data pointer, carry flag, skip flag, register A, and regis-
ter B just before an interrupt until returning to the original routine.
Unlike the stack registers (SKs), this register (SDP) is not used
when executing the subroutine call instruction and the table refer-
ence instruction.
(7) Skip flag
Skip flag controls skip decision for the conditional skip instructions
and continuous described skip instructions. When an interrupt oc-
curs, the contents of skip flag is stored automatically in the interrupt
stack register (SDP) and the skip condition is retained.
Fig. 5 Stack registers (SKs) structure
Fig. 6 Example of operation at subroutine call
SK0
SK1
SK2
SK3
SK4
SK5
SK6
SK7
(SP) = 0
(SP) = 1
(SP) = 2
(SP) = 3
(SP) = 4
(SP) = 5
(SP) = 6
(SP) = 7
Program counter (PC)
Executing RT
instruction
Executing BM
instruction
Stack pointer (SP) points “7” at reset or
returning from RAM back-up mode. It points “0”
by executing the first BM instruction, and the
contents of program counter is stored in SK0.
When the BM instruction is executed after eight
stack registers are used ((SP) = 7), (SP) = 0
and the contents of SK0 is destroyed.
Returning to the BM instruction execution
address with the RT instruction, and the BM
instruction becomes the NOP instruction.
(SP)
← 0
(SK0)
← 000116
(PC)
← SUB1
Main program
000216 NOP
Address
000016 NOP
000116 BM SUB1
Subroutine
SUB1 :
NOP
RT
(PC)
← (SK0)
(SP)
← 7
Note :
相關PDF資料
PDF描述
M34507M2-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO24
M34509G4FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24
M34513M4-XXXFP 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP32
M34514M6-XXXFP 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDSO42
M34514M8-XXXFP 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDSO42
相關代理商/技術參數
參數描述
M34508G4FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34508G4GP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34508G4GP#U0 功能描述:MCU 2/5V 4096 QZROM PB-FREE 20-S RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:720/4500 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO,I²C,LIN,UART/USART 外圍設備:DMA,LVD,POR,PWM,WDT 輸入/輸出數:27 程序存儲器容量:16KB(16K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤
M34508G4GP(#UO) 制造商:Renesas Electronics Corporation 功能描述:
M34508G4HFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER