參數資料
型號： M30240S9-XXXFP
廠商： Mitsubishi Electric Corporation
英文描述： 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
中文描述： 單片16位CMOS微機
文件頁數： 141/142頁
文件大?。?/td> 1637K
代理商： M30240S9-XXXFP
1-141
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Preliminary Specifications REV. E
Specifications in this manual are tentative and subject to change
Programming Notes
5.5 Programming Notes
5.5.1 Accessing USB IN/OUT CSR Registers
Do not use read-modify-write instruction on these registers because they contain control and status
bits that can be changed by both hardware and software. There is a possibility that using a read-mod-
ify-write instruction might cause incorrect data to be written back to these registers. See Table 1.53
for a list of bits that may have incorrect data written to them and the value you should write back in
order to prevent this from occurring.
The endpoint 1-4 IN CSR’s (EPiICS, i = 1-4) have a bit IN_PKT_RDY (bit 0) that is set to a “1” by the
firmware after a packet of data is loaded to the respective endpoint’s FIFO. This signifies that a packet
is ready for transmission. If the firmware wants to send a NULL packet to the host, it can simply write
a “1” to the IN_PKT_RDY bit without loading data to the FIFO. This bit is cleared by the hardware. If
the firmware manipulates (writes) the IN CSR for a purpose other than to signify to the hardware that
a data packet is ready for transmission (for instance, set/reset ISO bit, set/reset SEND_STALL bit), it
must make sure that a “0” is written back to the IN_PKT_RDY bit. Failure to do so could cause improp-
er operation of the device. Writing a “0” to the IN_PKT_RDY bit has no effect on its state.
The endpoint 1-4 OUT CSRs (EPiICS, i = 1-4) have a bit OUT_PKT_RDY (bit 0) that is set to a “1” by
the hardware after a packet of data is received from the host to the respective endpoint’s FIFO. This
signifies that a packet is ready for download. This bit is cleared by the firmware by writing a “0” to it
after the data packet is unloaded from the FIFO. If the firmware manipulates (writes) the OUT CSR for
a purpose other than to signify to the hardware that a data packet has been unloaded (for instance,
set/reset ISO bit, set/reset SEND_STALL bit), it must make sure that a “1” is written back to the
OUT_PKT_RDY bit. Failure to do so could cause improper operation. Writing a “1” to the
OUT_PKT_RDY bit has no effect on its state.
Table 1.53:
Bits that might have incorrect data
Register name
Bit name
Value to write for “No change”
EP0CS
IN_PKT_RDY (b1)
“0”
DATA_END (b3)
“0”
FORCE_STALL (b4)
“1”
EPxICS (x = 1-4)
IN_PKT_RDY (b0)
“0”
UNDER_RUN (b1)
“1”
EPxOCS (x = 1-4)
OUT_PKT_RDY (b0)
“1”
OVER_RUN (b1)
“1”
FORCE_STALL (b4)
“1”
DATA-ERR (b5)
“1”
相關PDF資料
PDF描述
M30245M4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245M8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M30240SA 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SA-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*