- 您現在的位置：買賣IC網 > PDF目錄224123 > M25P40SVMN6P/4 (NUMONYX) 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M25P40SVMN6P/4 |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8 |
| 文件頁數： | 29/57頁 |
| 文件大?。?/td> | 1160K |
| 代理商： | M25P40SVMN6P/4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
M25P40
Power-up and Power-down
35/57
7
Power-up and Power-down
At Power-up and Power-down, the device must not be selected (that is Chip Select (S) must
follow the voltage applied on VCC) until VCC reaches the correct value:
VCC(min) at Power-up, and then for a further delay of tVSL
VSS at Power-down
A safe configuration is provided in Section 3: SPI modes.
To avoid data corruption and inadvertent write operations during power-up, a Power On
Reset (POR) circuit is included. The logic inside the device is held reset while VCC is less
than the Power On Reset (POR) threshold voltage, VWI – all operations are disabled, and
the device does not respond to any instruction.
Moreover, the device ignores all Write Enable (WREN), Page Program (PP), Sector Erase
(SE), Bulk Erase (BE) and Write Status Register (WRSR) instructions until a time delay of
tPUW has elapsed after the moment that VCC rises above the VWI threshold. However, the
correct operation of the device is not guaranteed if, by this time, VCC is still below VCC(min).
No Write Status Register, Program or Erase instructions should be sent until the later of:
tPUW after VCC passed the VWI threshold
tVSL after VCC passed the VCC(min) level
These values are specified in Table 9.
If the delay, tVSL, has elapsed, after VCC has risen above VCC(min), the device can be
selected for READ instructions even if the tPUW delay is not yet fully elapsed.
At Power-up, the device is in the following state:
The device is in the Standby Power mode (not the Deep Power-down mode).
The Write Enable Latch (WEL) bit is reset.
The Write In Progress (WIP) bit is reset.
Normal precautions must be taken for supply rail decoupling, to stabilize the VCC supply.
Each device in a system should have the VCC rail decoupled by a suitable capacitor close to
the package pins. (Generally, this capacitor is of the order of 100 nF).
At Power-down, when VCC drops from the operating voltage, to below the Power On Reset
(POR) threshold voltage, VWI, all operations are disabled and the device does not respond
to any instruction. (The designer needs to be aware that if a Power-down occurs while a
Write, Program or Erase cycle is in progress, some data corruption can result.)
相關PDF資料 |
PDF描述 |
|---|---|
| M25P40SVMN3G/4A | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40-VMN6TG/X | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40VMF6 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P40VMF6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P40VMF6P | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P40-VMB3TPB | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M25P40-VMB3TPB TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 75MHZ 8UFDFPN |
| M25P40-VMB6TPB | 制造商:Micron Technology Inc 功能描述:4MBIT SPI NOR FLASH 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Cut TR (SOS) 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Tape and Reel 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 2.5V/3.3V 4Mbit 512K x 8bit 8ns 8-Pin UFDFPN EP T/R |
| M25P40-VMB6TPB TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 75MHZ 8UFDFPN |
| M25P40-VMB6Txx | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Micron M25P40 Serial Flash Embedded Memory |
發布緊急采購，3分鐘左右您將得到回復。