- 您現在的位置：買賣IC網 > PDF目錄224123 > M25P40SVMN6P/4 (NUMONYX) 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M25P40SVMN6P/4 |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8 |
| 文件頁數： | 24/57頁 |
| 文件大?。?/td> | 1160K |
| 代理商： | M25P40SVMN6P/4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Instructions
M25P40
30/57
6.9
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh) all bits inside the chosen sector. Before it
can be accepted, a Write Enable (WREN) instruction must previously have been executed.
After the Write Enable (WREN) instruction has been decoded, the device sets the Write
Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code, and three address bytes on Serial Data input (D). Any address inside the
Sector (see Table 3) is a valid address for the Sector Erase (SE) instruction. Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in Figure 15.
Chip Select (S) must be driven High after the eighth bit of the last address byte has been
latched in, otherwise the Sector Erase (SE) instruction is not executed. As soon as Chip
Select (S) is driven High, the self-timed Sector Erase cycle (whose duration is tSE) is
initiated. While the Sector Erase cycle is in progress, the Status Register may be read to
check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1
during the self-timed Sector Erase cycle, and is 0 when it is completed. At some unspecified
time before the cycle is completed, the Write Enable Latch (WEL) bit is reset.
A Sector Erase (SE) instruction applied to a page which is protected by the Block Protect
Figure 15.
Sector Erase (SE) instruction sequence
1. Address bits A23 to A19 are Don’t Care.
24 Bit Address
C
D
AI03751D
S
2
1
3456789
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25P40SVMN3G/4A | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40-VMN6TG/X | 512K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M25P40VMF6 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P40VMF6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P40VMF6P | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P40-VMB3TPB | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M25P40-VMB3TPB TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 75MHZ 8UFDFPN |
| M25P40-VMB6TPB | 制造商:Micron Technology Inc 功能描述:4MBIT SPI NOR FLASH 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Cut TR (SOS) 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Tape and Reel 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 2.5V/3.3V 4Mbit 512K x 8bit 8ns 8-Pin UFDFPN EP T/R |
| M25P40-VMB6TPB TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 75MHZ 8UFDFPN |
| M25P40-VMB6Txx | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Micron M25P40 Serial Flash Embedded Memory |
發布緊急采購，3分鐘左右您將得到回復。