- 您現在的位置：買賣IC網 > PDF目錄3796 > LPC11U14FHN33/201, (NXP Semiconductors)IC MCU 32BIT 32K 33HVQFN PDF資料下載
參數資料
| 型號： | LPC11U14FHN33/201, |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 20/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 32BIT 32K 33HVQFN |
| 產品培訓模塊： | Code Density for LPC11xx |
| 標準包裝： | 260 |
| 系列： | LPC11Uxx |
| 核心處理器： | ARM? Cortex?-M0 |
| 芯體尺寸： | 32-位 |
| 速度： | 50MHz |
| 連通性： | I²C，Microwire，智能卡，SPI，SSP，UART/USART，USB |
| 外圍設備： | 欠壓檢測/復位，POR，WDT |
| 輸入/輸出數： | 26 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 6K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 32-VQFN 裸露焊盤 |
| 包裝： | 托盤 |
| 其它名稱： | 568-8581 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
LPC11U1X
All information provided in this document is subject to legal disclaimers.
NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet
Rev. 2.2 — 11 March 2014
27 of 72
NXP Semiconductors
LPC11U1x
32-bit ARM Cortex-M0 microcontroller
Power-down mode reduces power consumption compared to Deep-sleep mode at the
expense of longer wake-up times.
7.16.5.5
Deep power-down mode
In Deep power-down mode, power is shut off to the entire chip with the exception of the
WAKEUP pin. The LPC11U1x can wake up from Deep power-down mode via the
WAKEUP pin.
The LPC11U1x can be prevented from entering Deep power-down mode by setting a lock
bit in the PMU block. Locking out Deep power-down mode enables the user to always
keep the watchdog timer or the BOD running.
When entering Deep power-down mode, an external pull-up resistor is required on the
WAKEUP pin to hold it HIGH. The RESET pin must also be held HIGH to prevent it from
floating while in Deep power-down mode.
7.16.6 System control
7.16.6.1
Reset
Reset has four sources on the LPC11U1x: the RESET pin, the Watchdog reset, power-on
reset (POR), and the BrownOut Detection (BOD) circuit. The RESET pin is a Schmitt
trigger input pin. Assertion of chip reset by any source, once the operating voltage attains
a usable level, starts the IRC and initializes the flash controller.
A LOW-going pulse as short as 50 ns resets the part.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the boot block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
An external pull-up resistor is required on the RESET pin if Deep power-down mode is
used.
7.16.6.2
Brownout detection
The LPC11U1x includes four levels for monitoring the voltage on the VDD pin. If this
voltage falls below one of the four selected levels, the BOD asserts an interrupt signal to
the NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the
NVIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading
a dedicated status register. Four additional threshold levels can be selected to cause a
forced reset of the chip.
7.16.6.3
Code security (Code Read Protection - CRP)
This feature of the LPC11U1x allows user to enable different levels of security in the
system so that access to the on-chip flash and use of the Serial Wire Debugger (SWD)
and In-System Programming (ISP) can be restricted. When needed, CRP is invoked by
programming a specific pattern into a dedicated flash location. IAP commands are not
affected by the CRP.
In addition, ISP entry via the PIO0_1 pin can be disabled without enabling CRP. For
details see the LPC11U1x user manual.
There are three levels of Code Read Protection:
相關PDF資料 |
PDF描述 |
|---|---|
| C8051F505-IQ | IC 8051 MCU 32K FLASH 48-QFP |
| EFM32TG108F32 | MCU 32BIT 32KB FLASH 24-QFN |
| P87C52X2FN,112 | IC 80C51 MCU 256 RAM 40DIP |
| LPC1224FBD64/121,1 | MCU 32BIT 48K FLASH 4K 64-LQFP |
| C8051F930-GM | IC 8051 MCU 64K FLASH 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC11U1X | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash; 6 kB SRAM; USB device; USART |
| LPC11U23FBD48 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash; up to 10 kB SRAM and 4 kB EEPROM; USB device; USART |
| LPC11U23FBD48/301 | 制造商:NXP Semiconductors 功能描述:MCU CORTEX M0 USB 48LQFP 制造商:NXP Semiconductors 功能描述:MCU, CORTEX M0, USB, 48LQFP 制造商:NXP Semiconductors 功能描述:MCU,50MHz,Cortex-M0,24KB Flash,LQFP48 |
| LPC11U23FBD48/301, | 功能描述:ARM微控制器 - MCU CortexM0 32bit 24KB with USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC11U23FBD48/301,551 | 制造商:NXP Semiconductors 功能描述:LPC11U2x Series 32-bit 24kB Flash 6 kB RAM ARM Cortex-M0 Microcontroller-LQFP-48 制造商:NXP 功能描述:LPC11U2x Series 32-bit 24kB Flash 6 kB RAM 50 MHz ARM Cortex-M0 Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。