- 您現在的位置：買賣IC網 > PDF目錄98000 > LM2633MTDX/NOPB (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 PDF資料下載
參數資料
| 型號： | LM2633MTDX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 31/40頁 |
| 文件大?。?/td> | 1350K |
| 代理商： | LM2633MTDX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Control Loop Design (Continued)
If aluminum, tantalum or OSCON capacitors are going to be
used, make sure the combined ESR is not greater than
10.6 m
.
Depending on the application, a different priority may be
assigned to the selection of components. For example, to
achieve a 10.6 m
combined ESR, it would require 6
low-ESR tantalum capacitors, which can be quite expensive.
If the inductor size is allowed to expand, then a higher
inductance value can be used so that ripple current is re-
duced and impedance of the capacitor at the switching fre-
quency can be higher. It is often necessary to go through
several iterations before a reasonable combination of the
inductor and capacitors is achieved.
Notice the above procedure is given without any consider-
ation of a load transient, whether expected or unexpected.
The power supply designer may be tempted to use a 100 F
ceramic capacitor as the only output capacitor in the above
example. That may be fine in a design that has a very static
load. However, should there be a large fault load current
(which is not enough to trigger UVP) and if later that condi-
tion is suddenly lifted, the output may see a severe over
voltage. Although the LM2633 will shut down immediately
upon seeing the over-voltage event, the load could have
been damaged already. Another concern with pure ceramic
output capacitors is soft start. It may be necessary to in-
crease the soft start time so that there will be minimum
overshoot at the end of soft start. So when a large induc-
tance and a small capacitance are chosen, care should be
given to the above situations.
If the load current goes from one level to another during
normal operations, a design with less capacitance tends to
have more output voltage excursion and recover more
slowly
than
one
with
more
capacitance.
From
the
time-domain viewpoint, that is because less capacitance is
less effective an energy buffer when the load current is
temporarily different from the inductor current. From the
frequency-domain viewpoint, that is because the output im-
pedance of the regulator is higher.
For power supplies that don’t have a stringent load transient
requirement, polymer aluminum capacitors can be used as
well as low-ESR tantalum capacitors. These polymer alumi-
num capacitors are surface mount, long-life, ignition free and
typically have very low ESR values. For example, Cornell
Dubilier’s ESRE and ESRD polymer aluminum chip capaci-
tors have ESR value as low as 6 m
and capacitance up to
270 F (http://www.cornell-dubilier.com).
Panasonic also offers specialty polymer aluminum capaci-
tors. Panasonic’s UE series offers capacitance up to 270 F,
and voltage rating up to 8 VDC.
For the Typical Application circuit, if there is no stringent load
transient requirement on Channel 1, C2 can be replaced by
a
single
polymer
aluminum
capacitor,
such
as
ESRE271M02R from Cornell Dubilier. The frequency com-
pensation should be: C14 = 4.7 nF, R9 = 7.5 k
. C15 and
R10 are not necessary. Notice that the voltage rating of that
capacitor is only 2 VDC.
Designing Around the Pulse-Skip Mode
If the FPWM pin is pulled to logic high, the LM2633 operates
in pulse-skip mode. In this mode, when the load is light
enough, the LM2633 starts to skip pulses. See
Pulse-Skip
Mode in Operation Descriptions.
In pulse-skip mode, the apparent switching frequency is
lower than the frequency the regulator would run at if it were
in force-PWM mode. The actual frequency depends on the
load, the lighter the load the lower the frequency.
The load at which pulse-skipping starts to happen can be
determined from the following formula:
(59)
Example: I
rip = 3A.
Since the critical load current completely depends on the
inductor ripple current, the inductance value cannot be arbi-
trary if accurate control of the value of the critical load is
desired.
When the FPWM pin is pulled high, the regulator enters the
discontinuous conduction mode (DCM) when the load is light
enough so that the inductor current goes to zero before the
end of each switching cycle. The critical load current value
for the regulator to enter DCM is:
(60)
Notice in DCM mode the FETs still switch every clock cycle
but the duty cycle shrinks as load current decreases. When
the load current goes below I
load_skip, the regulator enters
the pulse-skip mode. So the DCM region is a very narrow
one.
So, when the peak-peak ripple current is 3A, the DCM
happens only when load current falls in the 1.1A to 1.5A
range. Above that range, the regulator is in continuous con-
duction mode (CCM), and below that range, the regulator
runs in pulse-skip mode.
Designing a Linear Regulator with Channel 3
Channel 3 of the LM2633 can be used to drive an external
NPN transistor and provide linear regulation. See
The output voltage is adjusted through the voltage divider,
and the equation is:
200008A7
FIGURE 19. Channel 3 Controlling an LDO
LM2633
www.national.com
37
相關PDF資料 |
PDF描述 |
|---|---|
| LM2635MX/NOPB | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM26480QSQX-CF/NOPB | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480QSQ-CF/NOPB | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQ-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQX-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2635 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5-Bit Programmable Synchronous Buck Regulator Controller |
| LM2635A WAF | 制造商:Texas Instruments 功能描述: |
| LM2635M | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM2635M/NOPB | 功能描述:IC REG SYNCH BUCK 5-BIT 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LM2635MX | 功能描述:IC REG SYNCH BUCK 5-BIT 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。