- 您現在的位置：買賣IC網 > PDF目錄98000 > LM2633MTDX/NOPB (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 PDF資料下載
參數資料
| 型號： | LM2633MTDX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 29/40頁 |
| 文件大?。?/td> | 1350K |
| 代理商： | LM2633MTDX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Control Loop Design (Continued)
When Q is higher than 0.5, there will be a double-pole at half
the switching frequency f
n. When Q is lower than 0.5, the
double-pole is damped and becomes two separate poles.
The lower the Q value is, the farther apart the two poles are.
When Q is too low (such as Q = 0.05 or lower), one of the
two high frequency poles may move well into the low fre-
quency region. When Q is too high (such as Q = 5 or higher),
there will be significant peaking at half the switching fre-
quency and the phase will rapidly go to 180 near it. This
typically results in a lower cross-over frequency so that the
peaking in the loop gain is well below the 0dB line.
Q is a function of duty cycle and the deepness of the ramp
compensation (m
c). See Equation (34). The larger the duty
cycle, the higher the Q value. The deeper the ramp compen-
sation, the lower the Q value. When the inductor current
ramp is too much smaller than the compensation ramp, one
of the two high frequency poles will move far into the low
frequency region and form a double-pole with the existing
low frequency pole f
p. That makes it a voltage-mode control.
The ramp compensation becomes deeper when inductance
is increased, or input voltage is decreased, or sense resis-
tance is decreased.
In the case of Channel 1 of LM2633, if L = 1 to 3H, V
in =5
to 24V, V
o = 0.925 to 2V, Rds = 5 to 20m, the Q value will
be between 0.65 and 0.2.
Audio Susceptibility
Audio susceptibility is the transfer function from input to
output. In a typical power supply design, it is desirable to
have as much attenuation in that transfer function as pos-
sible so that noise appearing at the input has little effect on
the output. The open-loop audio susceptibility given by the
model in
Figure 7 is:
(47)
The closed-loop audio susceptibility is simply:
(48)
where H(s) is the compensation transfer function defined by:
(49)
It can be seen from
Equation (47) that if m
c is equal to
1/(2D’)+0.5, then the open-loop audio susceptibility is zero.
Unfortunately, the transfer function is rather sensitive to the
value of m
c around the critical value and thus this phenom-
enon is of little value.
The open-loop and closed-loop audio susceptibility of the
previous example is shown in
Figure 16. It can be told, both
from the model and from
Equation (47), that open-loop gain
of audio susceptibility is just a level shift of the loop gain.
Closed-loop audio susceptibility starts to depart from its
open-loop counterpart when frequency drops below the
cross-over frequency.
Adjusting the Output Voltages of the Switching
Channels
Channel 1 output voltage is normally adjusted through the
VID pins. Channel 2 output voltage is adjusted through an
external voltage divider, as shown in
The equation to find the value of R
2 when R1 has been
selected is:
(50)
where V
fb2 is equal to the internal reference voltage con-
nected to the non-inverting input of the Channel 2 error
20000878
FIGURE 15. How Control-Output Transfer Function
Changes with Q Values
20000882
FIGURE 16. Example Audio Susceptibility Gain
200008B7
FIGURE 17. Setting the Ch2 Output Voltage
LM2633
www.national.com
35
相關PDF資料 |
PDF描述 |
|---|---|
| LM2635MX/NOPB | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM26480QSQX-CF/NOPB | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480QSQ-CF/NOPB | 2.4 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQ-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
| LM26480SQX-BF/NOPB | 2.4 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, QCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2635 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5-Bit Programmable Synchronous Buck Regulator Controller |
| LM2635A WAF | 制造商:Texas Instruments 功能描述: |
| LM2635M | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM2635M/NOPB | 功能描述:IC REG SYNCH BUCK 5-BIT 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LM2635MX | 功能描述:IC REG SYNCH BUCK 5-BIT 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。