參數資料
型號： KFM4GH6Q4M-DEB80
元件分類： PROM
英文描述： 256M X 16 FLASH 1.8V PROM, 70 ns, PBGA63
封裝： 10 X 13 MM, 1 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, FBGA-63
文件頁數： 131/142頁
文件大?。?/td> 2226K
代理商： KFM4GH6Q4M-DEB80
Flex-MuxOneNAND4G(KFM4GH6Q4M-DEBx)
- 89 -
FLASH MEMORY
Flex-MuxOneNAND8G(KFN8GH6Q4M-DEBx)
Flex-MuxOneNAND16G(KFKAGH6Q4M-DEBx)
3.12.1.3 PI Block Program Operation
The PI Block Program Operation accesses the PI area and programs content from the DataRAM on-chip buffer to the designated page(s) of
the PI.
A memory location in the PI area can be program.
The PI area is programmed using the same sequence as normal program operation after being accessed by the PI Block Access mode entry
command (see section 3.8 for more information).
Programming the PI Area
Issue the PI Access Command(Refer to Chapter 3.12.1.1).
Write data into the DataRAM
- In case of PI Lock(Add: 0200h, DQ=3XXXh, The lower 10 bits[9:0] are boundary address) .
- In case of PI Unlock(Add: 0200h, DQ=FXXXh, The lower 10 bits[9:0] are boundary address).
Write 0000h into Flash Block Address (FBA), that is address of NAND Flash Array address map.
Issue a Program command to program the data from the DataRAM into the PI.
PI Block Program Operation Flow Chart (In PI Block Access Mode)
Locking the PI
Programming to PI block can be prevented by locking the PI area. Locking the PI area is accomplished by programming 3XXXh to 1st word of
sector0 of main of the page0 memory area in the PI block(XXXh out of 3XXXh is a boundary block address that ends SLC area).
Once Lock bits are programmed as lock status, PI block will be protected from program and erase. Boundary address is alterable before PI
block is locked, but it is not recommended.
At device power-up and PI Update operation, this word is updated internally. If 3XXXh is found(i.e. the status of PI is locked), Program/Erase
operations to PI block result in an error and the device updates the Error Bit of the Controller Status Register as "1"(fail).
NOTE :
1) Only the 1st word of 1st page of PI block (PI block Boundary Information) can be programmed in PI Block.
The rest of the block cannot be programmed.
2) FBA(NAND Flash Block Address) must be 0000h.
3) FPA must be 00h and FSA must be 00.
4) BSA must be 1000 and BSC must be 000.
5) ‘Write 0 to interrupt register’ step may be ignored when using INT auto mode. Refer to chapter 2.8.18.1
Start
Write ‘FPA, FSA’ of Flash
Add: F107h DQ=0000h3)
Write Data into DataRAM
Add: 0200h DQ= 1 word1)
PI Programming completed
Write Program command
DQ=0080h
Wait for INT register
low to high transition
Add: F241h DQ[15]=INT
Add: F220h
Write 0 to interrupt register5)
Add: F241h DQ=0000h
NO
* DBS, DFS is for DDP
Read Controller
Status Register
Add: F240h
DQ[10]=1(Error)
YES
Write ‘BSA, BSC’ of DataRAM
Add: F200h DQ=0800h4)
Write ‘DFS, FBA’ of Flash
Add: F100h DQ=FBA2)
PI Program Error
相關PDF資料
PDF描述
KHP7 2.75 A, 7000 V, SILICON, RECTIFIER DIODE
KJA1Y13K8PC 8 CONTACT(S), STEEL, MALE, MIL SERIES CONNECTOR, SOLDER, RECEPTACLE
KJA1Y13K8PD 8 CONTACT(S), STEEL, MALE, MIL SERIES CONNECTOR, SOLDER, RECEPTACLE
KJA1Y13K8PE 8 CONTACT(S), STEEL, MALE, MIL SERIES CONNECTOR, SOLDER, RECEPTACLE
KJA1Y13K8PN 8 CONTACT(S), STEEL, MALE, MIL SERIES CONNECTOR, SOLDER, RECEPTACLE
相關代理商/技術參數
參數描述
KFM65MZ-160PR 制造商:TYAN 功能描述:CHASSIS UNIT - Bulk
KFM85M 制造商:KEC 制造商全稱:KEC(Korea Electronics) 功能描述:SPECIFICATIONS FOR SAW FILTER(BAND PASS FILTERS FOR CDMA IF STAGE)
KFM90D060 制造商:IDEC CORPORATION 功能描述:CONNECTOR M12
KFM90D060R 制造商:IDEC CORPORATION 功能描述:CONNECTOR M12
KFM90D150 制造商:IDEC CORPORATION 功能描述:CONNECTOR M12
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*