- 您現在的位置：買賣IC網 > PDF目錄384536 > ISPGDX80VA-3T100 (LATTICE SEMICONDUCTOR CORP) In-System Programmable 3.3V Generic Digital CrosspointTM PDF資料下載
參數資料
| 型號： | ISPGDX80VA-3T100 |
| 廠商： | LATTICE SEMICONDUCTOR CORP |
| 元件分類： | PLD |
| 英文描述： | In-System Programmable 3.3V Generic Digital CrosspointTM |
| 中文描述： | EE PLD, 3 ns, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 4/27頁 |
| 文件大小： | 346K |
| 代理商： | ISPGDX80VA-3T100 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
4
Specifications
ispGDX80VA
Flexible mapping of MUXsel
x
to MUX
x
allows the user to
change the MUX select assignment after the ispGDXVA
device has been soldered to the board. Figure 1 shows
that the I/O cell can accept (by programming the appro-
priate fuses) inputs from the MUX outputs of four adjacent
I/O cells, two above and two below. This enables cascad-
ing of the MUXes to enable wider (up to 16:1) MUX
implementations.
The I/O cell also includes a programmable flow-through
latch or register that can be placed in the input or output
path and bypassed for combinatorial outputs. As shown
in Figure 1, when the input control MUX of the register/
latch selects the
“
A
”
path, the register/latch gets its inputs
from the 4:1 MUX and drives the I/O output. When
selecting the
“
B
”
path, the register/latch is directly driven
by the I/O input while its output feeds the GRP. The
programmable polarity Clock to the latch or register can
be connected to any I/O in the I/O-CLK/CLKEN set (one-
quarter of total I/Os) or to one of the dedicated clock input
pins (Y
x
). The programmable polarity Clock Enable input
to the register can be programmed to connect to any of
the I/O-CLK/CLKEN input pin set or to the global clock
enable inputs (CLKEN
x
). Use of the dedicated clock
inputs gives minimum clock-to-output delays and mini-
mizes delay variation with fanout. Combinatorial output
mode may be implemented by a dedicated architecture
bit and bypass MUX. I/O cell output polarity can be
programmed as active high or active low.
MUX Expander Using Adjacent I/O Cells
The ispGDXVA allows adjacent I/O cell MUXes to be
cascaded to form wider input MUXes (up to 16 x 1)
without incurring an additional full Tpd penalty. However,
there are certain dependencies on the locality of the
adjacent MUXes when used along with direct MUX
inputs.
Adjacent I/O Cells
Expansion inputs MUXOUT[n-2], MUXOUT[n-1],
MUXOUT[n+1], and MUXOUT[n+2] are fuse-selectable
for each I/O cell MUX. These expansion inputs share the
same path as the standard A, B, C and D MUX inputs, and
allow adjacent I/O cell outputs to be directly connected
without passing through the global routing pool. The
relationship between the [N+i] adjacent cells and A, B, C
and D inputs will vary depending on where the I/O cell is
located on the physical die. The I/O cells can be grouped
into
“
normal
”
and
“
reflected
”
I/O cells or I/O
“
hemi-
spheres.
”
These are defined as:
I/O MUX Operation
MUX1
0
0
1
MUX0
0
1
1
Data Input Selected
M0
M1
M2
1
0
M3
Device
Normal I/O Cells
Reflected I/O Cells
B9-B0, A19-A0,
D19-D10
B19-B0, A39-A0,
D39-D20
B10-B19, C0-C19,
D0-D9
B20-B39, C0-C39,
D0-D19
ispGDX80VA
ispGDX160V/VA
ispGDX240VA
B29-B0, A59-A0,
D59-D30
B30-B59, C0-C59,
D0-D29
Table 2 shows the relationship between adjacent I/O
cells as well as their relationship to direct MUX inputs.
Note that the MUX expansion is circular and that I/O cell
B10, for example, draws on I/Os B9 and B8, as well as
B11 and B12, even though they are in different hemi-
spheres of the physical die. Table 2 shows some typical
cases and all boundary cases. All other cells can be
extrapolated from the pattern shown in the table.
D10
D9
B9
B10
A
A
C
C
D19
B0
D0
B19
I/O cell 0
I/O cell 79
I/O cell 39
I/O cell 40
I
I
Figure 2. I/O Hemisphere Configuration of
ispGDX80VA
Direct and Expander Input Routing
Table 2 also illustrates the routing of MUX direct inputs
that are accessible when using adjacent I/O cells as
inputs. Take I/O cell D13 as an example, which is also
shown in Figure 3.
相關PDF資料 |
PDF描述 |
|---|---|
| ISPGDX80VA-5T100 | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPGDX80VA-5T100I | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPGDX80VA-7T100I | PHOTOELECTRIC PRODUCTS |
| ISPGDX80VA-9T100I | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPL1048E-125LQI | High-Density Programmable Logic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISPGDX80VA3T100-5I | 制造商:Lattice Semiconductor Corporation 功能描述: |
| ISPGDX80VA-3TN100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA5T100 | 制造商:Lattice Semiconductor Corporation 功能描述: |
| ISPGDX80VA-5T100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-5T100I | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。