- 您現在的位置：買賣IC網 > PDF目錄384536 > ISPGDX80VA-3T100 (LATTICE SEMICONDUCTOR CORP) In-System Programmable 3.3V Generic Digital CrosspointTM PDF資料下載
參數資料
| 型號： | ISPGDX80VA-3T100 |
| 廠商： | LATTICE SEMICONDUCTOR CORP |
| 元件分類： | PLD |
| 英文描述： | In-System Programmable 3.3V Generic Digital CrosspointTM |
| 中文描述： | EE PLD, 3 ns, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 24/27頁 |
| 文件大?。?/td> | 346K |
| 代理商： | ISPGDX80VA-3T100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁
24
Specifications
ispGDX80VA
I/O
Input/Output Pins
–
These are the general purpose bidirectional data pins. When used as outputs,
each may be independently latched, registered or tristated. They can also each assume one other
control function (OE, CLK/CLKEN, and MUXsel as described in the text).
This pin can be configured by the user through software to act as a
RESET
pin or as an I/O (I/O D10)
The default is
RESET
. If programmed to act as
RESET
, this pin is an active LOW Input Pin and resets
all I/O Register outputs when LOW.
Input Pins
–
These can be either Global Clocks or Clock Enables. In addition, Y1 is multiplexed with
TOE. Each pin can drive any or all I/O cell registers. The Test Output Enable (TOE) pin tristates all I/O
pins when LOW
Input Pin
–
JTAG TAP Controller Enable Pin. When high, JTAG operation is enabled. When low,
JTAG TAP controller is driven to reset.
Input Pin
–
Serial data input during ISP programming or Boundary Scan mode.
Input Pin
–
Serial data clock during ISP programming or Boundary Scan mode.
Input Pin
–
Control input during ISP programming or Boundary Scan mode.
Output Pin
–
Serial data output during ISP programming or Boundary Scan mode.
Ground (GND)
Vcc
–
Supply voltage (3.3V).
Input
–
This pin is used if optional 2.5V output is to be used. Every I/O can independently select either
3.3V or the optional voltage as its output level. If the optional output voltage is not required, this pin
must be connected to the VCC supply. Programmable pull-up resistors and bus-hold latches only draw
current from this supply.
RESET
/ I/O D10
Y1/CLKEN1/TOE,
Y0/CLKEN0
EPEN
TDI
TCK
TMS
TDO
GND
VCC
VCCIO
Signal Descriptions
Signal Name Description
相關PDF資料 |
PDF描述 |
|---|---|
| ISPGDX80VA-5T100 | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPGDX80VA-5T100I | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPGDX80VA-7T100I | PHOTOELECTRIC PRODUCTS |
| ISPGDX80VA-9T100I | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPL1048E-125LQI | High-Density Programmable Logic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISPGDX80VA3T100-5I | 制造商:Lattice Semiconductor Corporation 功能描述: |
| ISPGDX80VA-3TN100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA5T100 | 制造商:Lattice Semiconductor Corporation 功能描述: |
| ISPGDX80VA-5T100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-5T100I | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。