- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9035CCPJ (Gennum Corporation) GENLINX II -TM GS9035C Serial Digital Reclocker PDF資料下載
參數資料
| 型號： | GS9035CCPJ |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX II -TM GS9035C Serial Digital Reclocker |
| 中文描述： | GENLINX二，商標GS9035C串行數字時鐘恢復器 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 490K |
| 代理商： | GS9035CCPJ |
GENNUM CORPORATION
20582 - 3
7 of 14
G
1.2 Phase Detector
The phase detector compares the phase of the PLL clock
with the phase of the incoming data signal and generates
error correcting timing pulses. The phase detector design
provides a linear transfer function between the input phase
and output timing pulses maximizing the input jitter
tolerance of the PLL.
1.3 Charge Pump
The charge pump takes the phase detector output timing
pulses and creates a charge packet that is proportional to
the system phase error. A unique differential charge pump
design ensures that the output phase does not drift when
data transitions are sparse. This makes the GS9035C ideal
for SMPTE 259M applications where pathological signals
have data transition densities of 0.05.
1.4 Loop Filter
The loop filter integrates the charge pump packets and
produces a VCO control voltage. The loop filter is
comprised of three external components which are
connected to pins LF+, LFS, and LF-. The loop filter design
is fully differential giving the GS9035C increased immunity
to PCB board noise.
The loop filter components are critical in determining the
loop bandwidth and damping of the PLL. Choosing these
component values is discussed in detail in the PLL Design
Guidelines section. Recommended values for SMPTE 259M
applications are shown in the Typical Application Circuit
diagram.
2. FREQUENCY ACQUISITION
The core PLL is able to lock if the incoming data rate and
the PLL clock frequency are within the PLL capture range
(which is slightly larger than the loop bandwidth). To assist
the PLL to lock to data rates outside of the capture range,
the GS9035C uses a frequency acquisition circuit.
The frequency acquisition circuit sweeps the VCO control
voltage such that the VCO frequency changes from -10% to
+10% of the center frequency. Figure 11 shows a typical
sweep waveform.
Fig. 11 Typical Sweep Form
The VCO frequency starts at point A and sweeps up
attempting to lock. If lock is not established during the up
sweep, the VCO is then swept down. The system is
designed such that the probability of locking within one
cycle period is greater than 0.999. If the system does not
lock within one cycle period, it will attempt to lock in the
subsequent cycle. In manual mode, the divider modulus is
fixed for all cycles. In auto mode, each subsequent cycle is
based on a different divider moduli as determined by the
internal 2-bit counter.
The average sweep time, t
swp
, is determined by the loop
filter component, C
LF1
, and the charge pump current,
Ι
CP
:
The nominal sweep time is approximately 121μs when
C
LF1
= 15nF and
Ι
CP
= 165μA (R
VCO
= 365
).
An internal system clock determines t
sys
(
see section 7,
Logic Circuit
).
3. LOGIC CIRCUIT
The GS9035C is controlled by a finite state logic circuit which
is clocked by an asynchronous system clock. That is, the
system clock is completely independent of the incoming data
rate. The system clock runs at low frequencies, relative to the
incoming data rate, and thus reduces interference to the PLL.
The period of the system clock is set by the COSC capacitor
and is
t
sys
= 9.6 x 10
4
x COSC [seconds]
The recommended value for t
sys
is 450μs (COSC = 4.7nF).
4. AUTO/MANUAL DATA RATE SELECT
The GS9035C can operate in either auto or manual data
rate select mode. The mode of operation is selected by a
single input pin (AUTO/MAN).
4.1 Auto Mode (AUTO/MAN = 1)
In auto mode, the GS9035C uses a 2-bit counter to
automatically cycle through four (SMPTE=1) or two
(SMPTE=0) different divider moduli as it attempts to acquire
lock. In this mode, the SS[1:0] pins are outputs and indicate
the current value of the divider moduli according to Table 2.
Note that for SMPTE = 0 and divider moduli of 2 and 4, the
PLL can correctly lock for two values of SS[1:0].
V
LF
t
swp
T
cycle
T
cycle
= t
swp
+ t
sys
t
sys
A
t
swp
= 4
3
C
Ι
[seconds]
LF1
LF1
相關PDF資料 |
PDF描述 |
|---|---|
| GS9035CCTJ | GENLINX II -TM GS9035C Serial Digital Reclocker |
| GS9062-CF | GS9062 HD-LINX-TM II SD-SDI and DVB-ASI Serializer |
| GS9062-CFE3 | GS9062 HD-LINX-TM II SD-SDI and DVB-ASI Serializer |
| GS9064-CKD | GS9064 SD SDI Adaptive Cable Equalizer |
| GS9064-CKDE3 | GS9064 SD SDI Adaptive Cable Equalizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9035CCTJ | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GENLINX II -TM GS9035C Serial Digital Reclocker |
| GS9060 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II SD-SDI and DVB-ASI Deserializer with Loop-Through Cable Driver |
| GS9060-CF | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Gennum Corporation 功能描述: |
| GS9060-CFE3 | 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:Receiver for SD-SDI & DVB-ASI |
發布緊急采購，3分鐘左右您將得到回復。