- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9035CCPJ (Gennum Corporation) GENLINX II -TM GS9035C Serial Digital Reclocker PDF資料下載
參數資料
| 型號： | GS9035CCPJ |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX II -TM GS9035C Serial Digital Reclocker |
| 中文描述： | GENLINX二，商標GS9035C串行數字時鐘恢復器 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 490K |
| 代理商： | GS9035CCPJ |
GENNUM CORPORATION
20582 - 3
12 of 14
G
When trace lengths become greater than 1in, controlled
impedance traces should be used. The recommended
interface for differential signals is shown in Figure 18. In this
case, a parallel resistor (R
LOAD
) is placed near the
GS9035C inputs to terminate the controlled impedance
trace. The value of R
LOAD
should be twice the value of the
characteristic impedance of the trace. Both traces should
be in a symmetric arrangement and same physical
transmission line dimensions since common-mode signals
or common-mode noise is not terminated. In addition,
series resistors, R
SOURCE
, can be placed near the driving
chip to serve as source terminations. They should be equal
to the value of the trace impedance. Assuming 800mV
output swings at the driver, R
LOAD
=100
, R
SOURCE
=50
and Z
O
= 50
.
Fig. 18 Recommended Interface for Differential Signals
Figure 19 shows the recommended interface when the
GS9035C is driven single-endedly. In this case, the input
must be AC-coupled and a matching resistor (Z
O
) must be
used.
Fig. 19 Recommended Interface for Single-Ended Driver
10.2 High Speed Outputs (SDO/SDO and SCO/SCO)
SDO/SDO and SCO/SCO are current mode outputs that
require external pullup resistors (
see Figure 20
). To
calculate the output sink current use the following
relationship:
Output Sink Current = Output Signal Swing / Pullup Resistor
A diode can be placed between V
cc
and the pullup resis
tors to reduce the common mode voltage by approximately
0.7 volts. When the output traces are longer than 1in,
controlled impedance traces should be used. The pullup
resistors should be placed at the end of the output traces
as they terminate the trace in its characteristic impedance
(75
).
Fig. 20 High Speed Outputs with External Pullups
DDI
DDI
R
SOURCE
R
LOAD
R
SOURCE
Z
O
Z
O
GS9035C
DDI
DDI
Z
O
GS9035C
V
CC
SDO
SDO
SCO
SCO
75
75
V
CC
75
75
GS9035C
相關PDF資料 |
PDF描述 |
|---|---|
| GS9035CCTJ | GENLINX II -TM GS9035C Serial Digital Reclocker |
| GS9062-CF | GS9062 HD-LINX-TM II SD-SDI and DVB-ASI Serializer |
| GS9062-CFE3 | GS9062 HD-LINX-TM II SD-SDI and DVB-ASI Serializer |
| GS9064-CKD | GS9064 SD SDI Adaptive Cable Equalizer |
| GS9064-CKDE3 | GS9064 SD SDI Adaptive Cable Equalizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9035CCTJ | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GENLINX II -TM GS9035C Serial Digital Reclocker |
| GS9060 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II SD-SDI and DVB-ASI Deserializer with Loop-Through Cable Driver |
| GS9060-CF | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Gennum Corporation 功能描述: |
| GS9060-CFE3 | 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:Receiver for SD-SDI & DVB-ASI |
發布緊急采購，3分鐘左右您將得到回復。