1-10 Revision 10 Boundary Scan Testing (BST) All eX devices are IEEE 1149.1 compliant. eX devices offer s" />
參數資料
型號: EX64-TQG64I
廠商: Microsemi SoC
文件頁數: 6/48頁
文件大?。?/td> 0K
描述: IC FPGA ANTIFUSE 3K 64-TQFP
標準包裝: 160
系列: EX
邏輯元件/單元數: 128
輸入/輸出數: 41
門數: 3000
電源電壓: 2.3 V ~ 2.7 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 85°C
封裝/外殼: 64-LQFP
供應商設備封裝: 64-TQFP(10x10)
eX FPGA Architecture and Characteristics
1-10
Revision 10
Boundary Scan Testing (BST)
All eX devices are IEEE 1149.1 compliant. eX devices offer superior diagnostic and testing capabilities by
providing Boundary Scan Testing (BST) and probing capabilities. These functions are controlled through
the special test pins (TMS, TDI, TCK, TDO and TRST). The functionality of each pin is defined by two
available modes: Dedicated and Flexible, and is described in Table 1-4. In the dedicated test mode, TCK,
TDI, and TDO are dedicated pins and cannot be used as regular I/Os. In flexible mode (default mode),
TMS should be set HIGH through a pull-up resistor of 10 k
. TMS can be pulled LOW to initiate the test
sequence.
Dedicated Test Mode
In Dedicated mode, all JTAG pins are reserved for BST; designers cannot use them as regular I/Os. An
internal pull-up resistor is automatically enabled on both TMS and TDI pins, and the TMS pin will function
as defined in the IEEE 1149.1 (JTAG) specification.
To select Dedicated mode, users need to reserve the JTAG pins in Microsemi's Designer software by
checking the Reserve JTAG box in the Device Selection Wizard (Figure 1-12). JTAG pins comply with
LVTTL/TTL I/O specification regardless of whether they are used as a user I/O or a JTAG I/O. Refer to
page 1-18 for detailed specifications.
Flexible Mode
In Flexible Mode, TDI, TCK and TDO may be used as either user I/Os or as JTAG input pins. The internal
resistors on the TMS and TDI pins are disabled in flexible JTAG mode, and an external 10 k
pull-
resistor to VCCI is required on the TMS pin.
To select the Flexible mode, users need to clear the check box for Reserve JTAG in the Device Selection
Wizard in Microsemi's Designer software. The functionality of TDI, TCK, and TDO pins is controlled by
the BST TAP controller. The TAP controller receives two control inputs, TMS and TCK. Upon power-up,
the TAP controller enters the Test-Logic-Reset state. In this state, TDI, TCK, and TDO function as user
I/Os. The TDI, TCK, and TDO pins are transformed from user I/Os into BST pins when the TMS pin is
LOW at the first rising edge of TCK. The TDI, TCK, and TDO pins return to user I/Os when TMS is held
HIGH for at least five TCK cycles.
Table 1-4 Boundary Scan Pin Functionality
Dedicated Test Mode
Flexible Mode
TCK, TDI, TDO are dedicated BST pins
TCK, TDI, TDO are flexible and may be used as I/Os
No need for pull-up resistor for TMS and TDI
Use a pull-up resistor of 10 k
on TMS
Figure 1-12 Device Selection Wizard
相關PDF資料
PDF描述
HSM36DSAS CONN EDGECARD 72POS R/A .156 SLD
BR24S16FVT-WE2 IC EEPROM 16KBIT 400KHZ 8TSSOP
EX64-TQ64I IC FPGA ANTIFUSE 3K 64-TQFP
HMM36DSAS CONN EDGECARD 72POS R/A .156 SLD
A3PN250-ZVQG100I IC FPGA NANO 250K GATES 100-VQFP
相關代理商/技術參數
參數描述
EX-662 制造商:Pro-Signal 功能描述:EXTENSION CABLE KVM 2M 制造商:PRO SIGNAL 功能描述:EXTENSION CABLE, KVM, 2M 制造商:pro-power 功能描述:; Cable Length - Imperial:6.56ft; Cable Length - Metric:2m; Jacket Color:Grey
EX-663 制造商:Pro-Signal 功能描述:EXTENSION CABLE KVM 3M 制造商:PRO SIGNAL 功能描述:EXTENSION CABLE, KVM, 3M 制造商:pro-power 功能描述:; Cable Length - Imperial:9.84ft; Cable Length - Metric:3m; Jacket Color:Grey
EX-664 制造商:Pro-Signal 功能描述:EXTENSION CABLE KVM 5M 制造商:PRO SIGNAL 功能描述:EXTENSION CABLE, KVM, 5M
EX6XL 制造商:Perfectvision 功能描述:PPC WEATHERPROOF F CONNRG6 UNIVERSAL DTV APPROVED 制造商:PERFECT VISION 功能描述:PPC WEATHERPROOF F CONN RG6 UNIVERSAL DTV APPROVED
EX6XL-PLPLUS 制造商:Perfectvision 功能描述:PPC Weatherproof F Compression Connector RG6 Universal Plenum 制造商:PERFECT VISION 功能描述:PPC WEATHERPROOF F CONN RG6 UNIVERSAL PLENUM