- 您現在的位置：買賣IC網 > PDF目錄17110 > EVAL-ADUC812QSZ (Analog Devices Inc)BOARD EVALUATION FOR ADUC812 PDF資料下載
參數資料
| 型號： | EVAL-ADUC812QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR ADUC812 |
| 產品培訓模塊： | Process Control |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC812 |
| 所含物品： | 評估板、電源、纜線、軟件和說明文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
REV.
ADuC812
–17–
without any interaction from the ADuC812 core. This mode
allows the ADuC812 to capture a contiguous sample stream at
full ADC update rates (200 kHz).
DMA Mode Configuration Example
To set the ADuC812 into DMA mode, a number of steps must
be followed.
1. The ADC must be powered down by setting MD1 and MD0
to 0 in ADCCON1.
2. The DMA Address pointer must be set to the start address of
where the ADC results are to be written. This is done by
writing to the DMA mode Address Pointers DMAL, DMAH,
and DMAP. DMAL must be written to first, followed by
DMAH, and then DMAP.
3. The external memory must be preconfigured. This consists of
writing the required ADC channel IDs into the top four bits of
every second memory location in the external SRAM, starting
at the first address specified by the DMA address pointer. As the
ADC DMA mode operates independently of the ADuC812
core, it is necessary to provide it with a stop command. This is
done by duplicating the last channel ID to be converted, fol-
lowed by “1111” into the next channel selection field. Figure 11
shows a typical preconfiguration of external memory.
11
00
11
00
11
10
0
01
0
1
00
10
00000AH
000000H
STOP COMMAND
REPEAT LAST CHANNEL
FOR A VALID STOP
CONDITION
CONVERT ADC CH#3
CONVERT TEMP SENSOR
CONVERT ADC CH#5
CONVERT ADC CH#2
Figure 11. Typical DMA External Memory Preconfiguration
4. The DMA is initiated by writing to the ADC SFRs in the
following sequence.
a. ADCCON2 is written to enable the DMA mode, i.e.,
MOV ADCCON2, #40H; DMA mode enabled.
b. ADCCON1 is written to configure the conversion time and
power-up of the ADC. It can also enable Timer 2 driven
conversions or External Triggered conversions if required.
c. ADC conversions are initiated by starting single/continuous
conversions, starting Timer 2 running for Timer 2 conver-
sions, or by receiving an external trigger.
When the DMA conversions are completed, the ADC interrupt
bit ADCI is set by hardware and the external SRAM contains the
new ADC conversion results as shown in Figure 12. It should be
noted that no result is written to the last two memory locations.
When the DMA mode logic is active, it is responsible for storing
the ADC results away from both the user and ADuC812 core
logic. As it writes the results of the ADC conversions to external
memory, it takes over the external memory interface from the core.
Thus, any core instructions that access the external memory
while DMA mode is enabled will not gain access to it. The core
will execute the instructions and they will take the same time to
execute, but they will not gain access to the external memory.
NO CONVERSION
RESULT WRITTEN HERE
CONVERSION RESULT
FOR ADC CH#3
CONVERSION RESULT
FOR TEMP SENSOR
CONVERSION RESULT
FOR ADC CH#5
CONVERSION RESULT
FOR ADC CH#2
11
00
11
00
11
10
0
01
0
1
00
10
00000AH
000000H
STOP COMMAND
Figure 12. Typical External Memory Configuration Post
ADC DMA Operation
The DMA logic operates from the ADC clock and uses pipelining
to perform the ADC conversions and access the external memory
at the same time. The time it takes to perform one ADC conver-
sion is called a DMA cycle. The actions performed by the logic
during a typical DMA cycle are shown in Figure 13.
WRITE ADC RESULT
CONVERTED DURING
PREVIOUS DMA CYCLE
READ CHANNEL ID
TO BE CONVERTED DURING
NEXT DMA CYCLE
CONVERT CHANNEL READ DURING PREVIOUS DMA CYCLE
DMA CYCLE
Figure 13. DMA Cycle
From the previous diagram, it can be seen that during one DMA
cycle the following actions are performed by the DMA logic.
1. An ADC conversion is performed on the channel whose ID
was read during the previous cycle.
2. The 12-bit result and the channel ID of the conversion per-
formed in the previous cycle are written to the external memory.
3. The ID of the next channel to be converted is read from
external memory.
For the previous example, the complete flow of events is shown
in Figure 13. Because the DMA logic uses pipelining, it takes
three cycles before the first correct result is written out.
Micro Operation during ADC DMA Mode
During ADC DMA mode, the MicroConverter core is free to
continue code execution, including general housekeeping and
communication tasks. However, it should be noted that MCU core
accesses to Ports 0 and 2 (which are being used by the DMA
controller) are gated OFF during ADC DMA mode of operation.
This means that even though the instruction that accesses the
external Ports 0 or 2 will appear to execute, no data will be seen
at these external ports as a result.
The MicroConverter core can be configured with an interrupt
to be triggered by the DMA controller when it has finished
filling the requested block of RAM with ADC results, allowing
the service routine for this interrupt to postprocess data without
any real-time timing constraints.
Offset and Gain Calibration Coefficients
The ADuC812 has two ADC calibration coefficients, one for offset
calibration and one for gain calibration. Both the offset and gain
calibration coefficients are 14-bit words, located in the Special
Function Register (SFR) area. The offset calibration coefficient
is divided into ADCOFSH (six bits) and ADCOFSL (eight bits),
F
相關PDF資料 |
PDF描述 |
|---|---|
| ECM30DCWD | CONN EDGECARD 60POS DIP .156 SLD |
| ADR03WARZ-R7 | IC VREF SERIES PREC 2.5V 8SOIC |
| SC43B-1R4 | INDUCTOR SMD 1.4UH 2.20A 7.96MHZ |
| REC5-2415SRWZ/H4/C | CONV DC/DC 5W 9-36VIN 15VOUT |
| VI-J4F-EZ | CONVERTER MOD DC/DC 72V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC814MK | 制造商:Analog Devices 功能描述:Evaluation Board For Micro-Converter, Small Packag 12-Bit ADC With Embedded Flash MCU 制造商:Analog Devices 功能描述:MICROCONVEMICROCNVRTR, SMALL PACKAG 12-BIT ADC W/ EMBEDDED F - Bulk 制造商:Analog Devices 功能描述:Microcontroller Development Tool |
| EVAL-ADUC814QS | 制造商:Analog Devices 功能描述:8052 ADUC814 QUICKSTART DEV KIT |
| EVAL-ADUC814QS-U | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
| EVAL-ADUC814QSZ | 功能描述:KIT DEV FOR ADUC814 MICROCONVRTR RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC814QSZ | 制造商:Analog Devices 功能描述:EVAL BOARD, ADUC814 8052 CORE ANALOG MCU |
發布緊急采購，3分鐘左右您將得到回復。