參數資料
型號: DS2151Q
廠商: DALLAS SEMICONDUCTOR
元件分類: Digital Transmission Controller
英文描述: DATACOM, FRAMER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 32/47頁
文件大?。?/td> 413K
代理商: DS2151Q
MAX1464
Low-Power, Low-Noise Multichannel
Sensor Signal Processor
38
Maxim Integrated
BIT
NAME
DESCRIPTION
15–12
PS[3:0]
Prescaler setting to use during the timing interval. PS[3 ] = MSB.
11–0
TO[11:0]
Timeout value to use during the timing interval. TO[11] = MSB.
Table 31. TMR_Config (Address = 21h)
BITS
NAME
DESCRIPTION
15–6
Unused.
5
OUT2
OUT2 value is driven onto the GPIO2 pin when the output driver is enabled.
4
EN2
Enable the output driver; 1 = enabled, 0 = disabled, and OUT tri-stated.
3
IN2
When EDGE2 = 0: The value input on GPIO2 is clocked into this bit (Notes 14, 15).
When EDGE2 = 1: An edge detection on GPIO2 causes a 1 to be clocked into this bit.
2
CLR2
Clear IN2 bit; 1 = clear IN2 to 0, 0 = IN2 retains its status (Note 16).
1
INV2
When EDGE2 = 0: Invert the logic value IN2; 1 = invert input, 0 = do not invert. When EDGE2 = 1: Select
edge capture type; 1 = falling edge detect; 0 = rising edge detect.
0
EDGE2
Select level or edge detection at IN2; 1 = detect edges, 0 = detect and track logic levels.
Table 29. GPIO2_Control (Address = 41h)
Note 14: A pulse or level must remain on GPIOn for four periods of fOSC to be latched into IN.
Note 15: The CLRn bit must be cleared to zero to reenable GPIO to value tracking.
Note 16: The CLRn bit must be cleared to zero to reenable GPIO edge detection.
BIT
NAME
DESCRIPTION
15
TMDN
Timer done bit set by the counter; 1 = timeout value reached, 0 = timeout not reached. Read-only
bit.
14
TMEN
Timer enable bit; A 1 written to TMEN resets TMDN to zero and starts counter. TMEN is reset to
zero by the counter when timeout value is reached.
13–1
Unused.
0
ENAHALT
Enable CPU halt; 1 = CPU halted for duration of timer interval, 0 = CPU not halted.
Table 30. TMR_Control (Address = 20h)
BITS
NAME
DESCRIPTION
15–6
Unused.
5
OUT1
OUT1 value is driven onto the GPIO1 pin when the output driver is enabled.
4
EN1
Enable the output driver; 1 = enabled, 0 = disabled, and OUT tri-stated.
3
IN1
When EDGE1 = 0: The value input on GPIO1 is clocked into this bit (Notes 14, 15).
When EDGE1 = 1: An edge detection on GPIO1 causes a 1 to be clocked into this bit.
2
CLR1
Clear IN1 bit; 1 = clear IN1 to 0, 0 = IN1 retains its status (Note 16).
1
INV1
When EDGE1 = 0: Invert the logic value IN1; 1 = invert input, 0 = do not invert. When EDGE1 = 1: Select
edge capture type; 1 = falling edge detect; 0 = rising edge detect.
0
EDGE1
Select level or edge detection at IN1; 1 = detect edges, 0 = detect and track logic levels.
Table 28. GPIO1_Control (Address = 40h)
相關PDF資料
PDF描述
DS229S LINE TRANSCEIVER, PDSO20
DS232AE LINE TRANSCEIVER, PDSO20
DS232AR LINE TRANSCEIVER, PDSO16
DS232AR-N LINE TRANSCEIVER, PDSO16
DS232AS-N LINE TRANSCEIVER, PDSO16
相關代理商/技術參數
參數描述
DS2151Q/T&R 制造商:Maxim Integrated Products 功能描述:IC TXRX T1 1-CHIP 5V LP 44-PLCC
DS2151Q/T&R 功能描述:IC TXRX T1 1-CHIP 5V LP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
DS2151QB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2151QB/T&R 制造商:Maxim Integrated Products 功能描述:T1 SINGLE CHIP XCVR REV B T&R - Tape and Reel
DS2151QB/T&R+ 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel