- 您現在的位置：買賣IC網 > PDF目錄379885 > CH1005C (Electronic Theatre Controls, Inc.) Digital PC to TV Encoder with Macrovision PDF資料下載
參數資料
| 型號： | CH1005C |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Digital PC to TV Encoder with Macrovision |
| 中文描述： | 數碼電腦電視編碼器和通過Macrovision |
| 文件頁數： | 27/49頁 |
| 文件大?。?/td> | 338K |
| 代理商： | CH1005C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
201-0000-025 Rev 2.1, 8/2/99
27
CHRONTEL
CH7005C
Note:
The acknowledge is from the CH7005 (slave).
Figure 22: Alternating Write Cycles
If AutoInc = 1, then the register address pointer will be incremented automatically and subsequent data bytes will be
written into successive registers without providing an RAB between each data byte. An Auto-increment write cycle
is shown in
Figure 23.
.
Note:
The acknowledge is from the CH7005 (slave).
Figure 23: Auto-Increment Write Cycle
When the auto-increment mode is enabled (AutoInc is set to 1), the register address pointer continues to increment
for each write cycle until AR[5:0] = 3F (3F is the address of the Address Register). The next byte of information
represents a new auto-sequencing “Starting address,” which is the address of the register to receive the next byte.
The auto-sequencing then resumes based on this new “Starting address.” The auto-increment sequence can be
terminated any time by either a “STOP” or “RESTART” condition. The write operation can be terminated with a
“STOP” condition.
CH7005 Read Cycle Protocols (R/W = 1)
If a master-receiver is involved in a transfer, it must signal the end of data to the slave-transmitter by not generating
an acknowledge on the last byte that was clocked out of the slave. The slave-transmitter CH7005 releases the data
line to allow the master to generate the STOP condition or the RESTART condition.
To read the content of the registers, the master device starts by issuing a “START” condition (or a “RESTART”
condition). The first byte of data, after the START condition, is a DAB with R/W = 0. The second byte is the RAB
with AR[5:0], containing the address of the register that the master device intends to read from in AR[5:0]. The
master device should then issue a “RESTART” condition (“RESTART” = “START,” without a previous “STOP”
condition). The first byte of data, after this RESTART condition, is another DAB with R/W=1, indicating the
master’s intention to read data hereafter. The master then reads the next byte of data (the content of the register
specified in the RAB). If AutoInc = 0, then another RESTART condition, followed by another DAB with R/W = 0
and RAB, is expected from the master device. The master device then issues another RESTART, followed by
another DAB. After that, the master may read another data byte, and so on. In summary, a RESTART condition,
followed by a DAB, must be produced by the master before each of the RAB, and before each of the data read
events. Two consecutive alternating read cycles are shown in
Figure 24
.
SD
SC
1 - 8
RAB
9
ACK
Condition
Start
Condition
Stop
1 - 7
Device ID
8
R/W*
9
ACK
CH7005
acknowledge
CH7005
acknowledge
1 - 8
RAB
9
ACK
CH7005
acknowledge
1 - 8
Data
9
ACK
I
2
C
1 - 8
Data
9
ACK
CH7005
acknowledge
CH7005
acknowledge
SD
SC
1 - 8
9
RAB n
ACK
Start
Condition
Stop
Condition
CH7005
acknowledge
1 - 8
Data n
9
1 - 8
9
ACK
Data n+1
ACK
CH7005
acknowledge
CH7005
acknowledge
CH7005
acknowledge
1 - 7
Device ID
8
R/W*
9
ACK
I
2
C
相關PDF資料 |
PDF描述 |
|---|---|
| CH7005C-T | Digital PC to TV Encoder with Macrovision |
| CH7005C-V | Digital PC to TV Encoder with Macrovision |
| CH1786 | CH1786 Family of Ultra Small 2400bps Modems |
| CH1840 | Low Profile Data Access Arrangement (DAA) Modules |
| CH5283 | HIGH RELIABILITY CURRENT REGULATOR DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CH1008EN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:機車瞞盜鍵專用IC |
| CH100GE | 制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:The industrya??s most compact 100 G test solution |
| CH100GEINOTU4 | 制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:The industrya??s most compact 100 G test solution |
| CH100SNC | 制造商:Square D by Schneider Electric 功能描述:NEUTRAL ASSY INSULATED GRDABLE-CU ONLY |
| CH101 | 功能描述:熔絲座 CH101 RoHS:否 制造商:Littelfuse 產品: 電流額定值:30 A 電壓額定值:1000 VDC 極數:1 系列: 安裝風格:DIN Rail 端接類型: 軸類型: 工作溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。