參數資料
型號： ATF1508RE-7AU100
廠商： Atmel
文件頁數： 32/54頁
文件大?。?/td> 0K
描述： IC CPLD EE 128MC 5NS 100-TQFP
標準包裝： 90
系列： ATF15xx
可編程類型： 系統內可編程（最少 10,000 次編程/擦除循環）
最大延遲時間 tpd(1)： 7.5ns
電壓電源 - 內部： 3 V ~ 3.6 V
宏單元數： 128
輸入/輸出數： 80
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP
供應商設備封裝： 100-TQFP（14x14）
包裝： 托盤
產品目錄頁面： 608 (CN2011-ZH PDF)
Atmel ATF15xx Family: ISP Devices User Guide
6-1
Section 6
JTAG ISP Guidelines
This section describes important guidelines and information about ISP that all users
must pay attention to when performing ISP operations on Atmel ISP devices.
1.
Make sure all ISP devices on your circuit board are erased before programming.
To prevent the use of the JTAG port pins by any of the ISP devices.
This will enable the JTAG port.
All Atmel ATF15xx devices are shipped in the erased state so that they are ISP-
ready.
2.
Make sure the red LED on the back of the Atmel-ISP cable is on when
programming.
To ensure that the ISP cable is connected properly.
3.
Verify that the correct ISP cable is used.
Atmel-ISP software defaults to using the Atmel-ISP cable.
Must change cable type if using ByteBlaster/ByteBlasterMV cable.
4.
If a parallel cable is used to connect the ISP cable to the PC’s parallel port, make
sure the parallel cable being used is 6 feet long or less.
Parallel cable longer than 6 feet might introduce communication problems
between the ISP cable and the parallel port.
5.
When using Atmel-ISP cable, make sure that the cable is connected to the
ISP\target board before powering up the ISP\target board. Once the ISP\target
board is powered up and the LED on the back of the ISP cable is turned on, then
connect the other side of the ISP cable to the PC’s parallel port.
To eliminate possible communication problem.
6.
Run Self-Calibrate or Manual Calibration if the software is having problems com-
municating with the JTAG device hardware chain.
Self-Calibrate and Manual Calibration allow the user to reduce the transfer
speed of the JTAG signals from the PC’s parallel port to the JTAG device chain.
7.
Make sure your parallel port settings are configured correctly.
The ISP software may have problems running on PCs with Auto mode configu-
ration for parallel port.
Change your BIOS port settings to either ECP or EPP mode.
Confirm your port address setting before using the software.
Default settings are: 0378H for LPT1; 0278H for LPT2.
Other port addresses must be entered manually.
Rev. 1936A-07/01
相關PDF資料
PDF描述
ATF16LV8C-10SI IC PLD EE 8CELL 3V LP 20-SOIC
ATF16V8BQL-15XC IC PLD 15NS 20TSSOP
ATF16V8C-7XU IC PLD 7NS 20TSSOP
ATF16V8CZ-15XC IC PLD 15NS 20TSSOP
ATF20V8BQL-15PU IC PLD 15NS 24DIP
相關代理商/技術參數
參數描述
ATF1508RE-7CU132 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Highperformance CPLD
ATF1508SE 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Family Datasheet
ATF1508SE(L) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ATF1502/04/08/16SE(L) Preliminary [Updated 9/02. 69 Pages] Second Generation Industry Compatible 5V Logic Doubling CPLDs 32-512 Macrocells. standard & low power w/ISP
ATF1508SL 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Family Datasheet
ATF1508Z 制造商:未知廠家 制造商全稱:未知廠家 功能描述:High Performance E2PLD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*