3. If 8 MHz frequency exceeds the specification of the device (depends on VCC" />
參數資料
型號: AT90USB82-16MUR
廠商: Atmel
文件頁數: 27/38頁
文件大?。?/td> 0K
描述: MCU AVR USB 8K FLASH 32-QFN
產品培訓模塊: MCU Product Line Introduction
megaAVR Introduction
標準包裝: 5,000
系列: AVR® 90USB
核心處理器: AVR
芯體尺寸: 8-位
速度: 16MHz
連通性: EBI/EMI,PS/2,SPI,UART/USART,USB
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 22
程序存儲器容量: 8KB(8K x 8)
程序存儲器類型: 閃存
EEPROM 大小: 512 x 8
RAM 容量: 512 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 32-VFQFN 裸露焊盤
包裝: 帶卷 (TR)
配用: ATSTK600-ND - DEV KIT FOR AVR/AVR32
ATSTK526-ND - KIT STARTER FOR AT90USB82/162
ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR
ATSTK525-ND - KIT STARTER FOR AT90USB
AT90USBKEY2-ND - KIT DEMO FOR AT90USB
33
7707F–AVR–11/10
AT90USB82/162
3. If 8 MHz frequency exceeds the specification of the device (depends on VCC), the CKDIV8
Fuse can be programmed in order to divide the internal frequency by 8.
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Note:
1. The device is shipped with this option selected.
6.5.1
Oscillator Calibration Register – OSCCAL
Bits 7..0 – CAL7..0: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to
remove process variations from the oscillator frequency. The factory-calibrated value is automat-
ically written to this register during chip reset, giving an oscillator frequency of 8.0 MHz at 25°C.
The application software can write this register to change the oscillator frequency. The oscillator
can be calibrated to any frequency in the range 7.3 - 8.1 MHz within ±1% accuracy. Calibration
outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write
times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more
than 8.8 MHz. Otherwise, the EEPROM or Flash write may fail.
The CAL7 bit determines the range of operation for the oscillator. Setting this bit to 0 gives the
lowest frequency range, setting this bit to 1 gives the highest frequency range. The two fre-
quency ranges are overlapping, in other words a setting of OSCCAL = 0x7F gives a higher
frequency than OSCCAL = 0x80.
The CAL6..0 bits are used to tune the frequency within the selected range. A setting of 0x00
gives the lowest frequency in that range, and a setting of 0x7F gives the highest frequency in the
range. Incrementing CAL6..0 by 1 will give a frequency increment of less than 2% in the fre-
quency range 7.3 - 8.1 MHz.
Table 6-7.
Start-up times for the internal calibrated RC Oscillator clock selection
Power Conditions
Start-up Time from Power-
down and Power-save
Additional Delay from
Reset (V
CC = 5.0V)
SUT1..0
BOD enabled
6 CK
14 CK
00
Fast rising power
6 CK
14 CK + 4.1 ms
01
Slowly rising power
6 CK
14 CK + 65 ms(1)
10
Reserved
11
Bit
7654
3
2
1
0
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
OSCCAL
Read/Write
R/WR/W
Initial Value
Device Specific Calibration Value
相關PDF資料
PDF描述
ADG201HSKR-REEL IC SWITCH QUAD SPST 16SOIC
ADG1406BRUZ-REEL7 IC MULTIPLEXER 8X1 28TSSOP
ADG201HSJPZ IC SWITCH QUAD SPST 20PLCC
ADG333ABR IC SWITCH QUAD SPDT 20SOIC
ADG333ABRS IC SWITCH QUAD SPDT 20SSOP
相關代理商/技術參數
參數描述
AT90USBKEY 功能描述:開發板和工具包 - AVR Demo board f/AVR MCU & AT90USB RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:ATMega32U4 核心:AVR 接口類型:I2C, UART, USB 工作電源電壓:6 V to 20 V
AT90USBKEY2 功能描述:開發板和工具包 - AVR AVR USB Eval Kit RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:ATMega32U4 核心:AVR 接口類型:I2C, UART, USB 工作電源電壓:6 V to 20 V
AT-910 制造商:HRS 制造商全稱:HRS 功能描述:Stripline Mounting Fixed Attenuators (DC to 8 GHz)
AT-910(40) 功能描述:衰減器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰減:18 dB 容差: 阻抗: 功率額定值:30 dBm 安裝風格:SMD/SMT 工作溫度范圍:- 40 C to + 85 C
AT-913(40) 功能描述:衰減器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰減:18 dB 容差: 阻抗: 功率額定值:30 dBm 安裝風格:SMD/SMT 工作溫度范圍:- 40 C to + 85 C