參數資料
型號： ADV7189BBSTZ
廠商： Analog Devices Inc
文件頁數： 33/104頁
文件大?。?/td> 0K
描述： IC VIDEO DECODER SDTV 80-LQFP
標準包裝： 1
類型： 視頻解碼器
應用： 機頂盒，視頻播放器，錄音機
電壓 - 電源，模擬： 3.15 V ~ 3.45 V
電壓 - 電源，數字： 1.65 V ~ 2 V
安裝類型： 表面貼裝
封裝/外殼： 80-LQFP
供應商設備封裝： 80-LQFP（14x14）
包裝： 托盤
ADV7189B
Rev. B | Page 34 of 104
CHROMA TRANSIENT IMPROVEMENT (CTI)
The signal bandwidth allocated for chroma is typically much
smaller than that of luminance. In the past, this was a valid
way to fit a color video signal into a given overall bandwidth
because the human eye is less sensitive to chrominance than
to luminance.
The uneven bandwidth, however, can lead to visual artifacts in
sharp color transitions. At the border of two bars of color, both
components (luma and chroma) change at the same time (see
194H
Figure 18). Due to the higher bandwidth, the signal transition
of the luma component is usually a lot sharper than that of the
chroma component. The color edge is not sharp but is blurred,
in the worst case, over several pixels.
04983-
0-
018
LUMA
SIGNAL
DEMODULATED
CHROMA
SIGNAL
LUMA SIGNAL WITH A
TRANSITION, ACCOMPANIED
BY A CHROMA TRANSITION
ORIGINAL, "SLOW" CHROMA
TRANSITION PRIOR TO CTI
SHARPENED CHROMA
TRANSITION AT THE
OUTPUT OF CTI
Figure 18. CTI Luma/Chroma Transition
The chroma transient improvement block examines the input
video data. It detects transitions of chroma, and can be pro-
grammed to “steepen” the chroma edges in an attempt to
artificially restore lost color bandwidth. The CTI block,
however, operates only on edges above a certain threshold
to ensure that noise is not emphasized. Care has also been
taken to ensure that edge ringing and undesirable saturation
or hue distortion are avoided.
Chroma transient improvements are needed primarily for sig-
nals that experienced severe chroma bandwidth limitation. For
those types of signals, it is strongly recommended to enable the
CTI block via CTI_EN.
CTI_EN Chroma Transient Improvement Enable,
Address 0x4D[0]
The CTI_EN bit enables the CTI function. If set to 0, the CTI
block is inactive and the chroma transients are left untouched.
Setting CTI_EN to 0 disables the CTI block.
Setting CTI_EN to 1 (default) enables the CTI block.
CTI_AB_EN Chroma Transient Improvement
Alpha Blend Enable, Address 0x4D[1]
The CTI_AB_EN bit enables an alpha-blend function within
the CTI block. If set to 1, the alpha blender mixes the transient
improved chroma with the original signal. The sharpness of the
alpha blending can be configured via the CTI_AB[1:0] bits.
For the alpha blender to be active, the CTI block must be
enabled via the CTI_EN bit.
Setting CTI_AB_EN to 0 disables the CTI alpha blender.
Setting CTI_AB_EN to 1 (default) enables the CTI alpha-blend
mixing function.
CTI_AB[1:0] Chroma Transient Improvement Alpha
Blend, Address 0x4D[3:2]
The CTI_AB[1:0] controls the behavior of alpha-blend circuitry
that mixes the sharpened chroma signal with the original one. It
thereby controls the visual impact of CTI on the output data.
For CTI_AB[1:0] to become active, the CTI block must be
enabled via the CTI_EN bit, and the alpha blender must be
switched on via CTI_AB_EN.
Sharp blending maximizes the effect of CTI on the picture, but
can also increase the visual impact of small amplitude, high
frequency chroma noise.
Table 43. CTI_AB Function
CTI_AB[1:0]
Description
00
Sharpest mixing between sharpened and original
chroma signal.
01
Sharp mixing.
10
Smooth mixing.
11 (default)
Smoothest alpha blend function.
CTI_C_TH[7:0] CTI Chroma Threshold, Address
0x4E[7:0]
The CTI_C_TH[7:0] value is an unsigned, 8-bit number speci-
fying how big the amplitude step in a chroma transition is to be
steepened by the CTI block. Programming a small value into
this register causes even smaller edges to be steepened by the
CTI block. Making CTI_C_TH[7:0] a large value causes the
block to only improve large transitions.
The default value for CTI_C_TH[7:0] is 0x08, indicating
the threshold for the chroma edges prior to CTI.
DIGITAL NOISE REDUCTION (DNR)
Digital noise reduction is based on the assumption that high
frequency signals with low amplitude are probably noise and
their removal, therefore, improves picture quality.
DNR_EN Digital Noise Reduction Enable, Address
0x4D[5]
The DNR_EN bit enables the DNR block or bypasses it.
Setting DNR_EN to 0 bypasses DNR (disables it).
Setting DNR_EN to 1 (default) enables digital noise reduction
on the luma data.
相關PDF資料
PDF描述
ADV7194KSTZ IC ENCODER VIDEO EXT-10 80-LQFP
ADV7202KSTZ IC CODEC VIDEO 10BIT 64LQFP
ADV7311KST IC VID ENC 6-12BIT DAC'S 64LQFP
ADV7321KSTZ IC VID ENC 6-12BIT DAC'S 64LQFP
ADV7343BSTZ IC ENCODER VIDEO W/DAC 64-LQFP
相關代理商/技術參數
參數描述
ADV7189BBSTZ268H 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder
ADV7189BBSTZ268H2 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder
ADV7189BKST 制造商:Analog Devices 功能描述:
ADV7189BKSTZ 功能描述:IC DECODER VIDEO W/ADC 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
ADV7189BKSTZ10F 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*