- 您現在的位置：買賣IC網 > PDF目錄374037 > ADSP-2196MBST-140X (ANALOG DEVICES INC) DSP Microcomputer PDF資料下載
參數資料
| 型號： | ADSP-2196MBST-140X |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | DSP Microcomputer |
| 中文描述： | 16-BIT, 160 MHz, OTHER DSP, PQFP144 |
| 封裝： | METRIC, PLASTIC, LQFP-144 |
| 文件頁數： | 18/68頁 |
| 文件大小： | 897K |
| 代理商： | ADSP-2196MBST-140X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
For current information contact Analog Devices at 800/262-5643
ADSP-2196
As can be seen in
Figure 7
, there are two sets of signals on
the header. There are the standard JTAG signals TMS,
TCK, TDI, TDO, TRST, and EMU used for emulation
purposes (via an emulator). There are also secondary JTAG
signals BTMS, BTCK, BTDI, and BTRST that are option-
ally used for board-level (boundary scan) testing.
When the emulator is not connected to this header, place
jumpers across BTMS, BTCK, BTRST, and BTDI as
shown in
Figure 8
. This holds the JTAG signals in the
correct state to allow the DSP to run free. Remove all the
jumpers when connecting the emulator to the JTAG header.
September 2001
This information applies to a product under development. Its characteristics and specifications are subject to change with-
out notice. Analog Devices assumes no obligation regarding future manufacturing unless otherwise agreed to in writing.
18
REV. PrA
JTAG Emulator Pod Connector
Figure 9
details the dimensions of the JTAG pod connector
at the 14-pin target end.
Figure 10
displays the keep-out
area for a target board header. The keep-out area allows the
pod connector to properly seat onto the target board header.
This board area should contain no components (chips,
resistors, capacitors, etc.). The dimensions are referenced
to the center of the 0.25" square post pin.
Design-for-Emulation Circuit Information
For details on target board design issues including: single
processor connections, multiprocessor scan chains, signal
buffering, signal termination, and emulator pod logic, see
the
EE-68: Analog Devices JTAG Emulation Technical
Reference
on the Analog Devices website (www.ana-
log.com)—use site search on “EE-68”. This document is
updated regularly to keep pace with improvements to
emulator support.
Additional Information
This data sheet provides a general overview of the
ADSP-2196 architecture and functionality. For detailed
information on the ADSP-219x family core architecture
and instruction set, refer to the
ADSP-219x/2191 DSP
Hardware Reference
.
PIN DESCRIPTIONS
ADSP-2196 pin definitions are listed in
Table 7
. All
ADSP-2196 inputs are asynchronous and can be asserted
asynchronously to CLKIN (or to TCK for TRST).
Unused inputs should be tied or pulled to V
DDEXT
or GND,
except for ADDR21–0, DATA15–0, PF7-0, and inputs that
have internal pull-up or pull-down resistors (TRST,
BMODE0, BMODE1, OPMODE, BYPASS, TCK, TMS,
TDI, and RESET)—these pins can be left floating. These
pins have a logic-level hold circuit that prevents input from
floating internally.
The following symbols appear in the Type column of
Table 7
: G = Ground, I = Input, O = Output, P = Power
Supply, and T = Three-State.
Figure 8. JTAG Target Board Connector with No Local
Boundary Scan
Figure 9. JTAG Pod Connector Dimensions
(%
"'
"
+
)
&
&
&
'.2
'.2
'.2
Figure 10. JTAG Pod Connector Keep-Out Area
'.'2
'.)2
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2196MKCA-160X | DSP Microcomputer |
| ADSP-2196MKST-160X | DSP Microcomputer |
| ADSP-21990 | 16-bit fixed point DSP with Flash |
| ADSP-21990BBC | 16-bit fixed point DSP with Flash |
| ADSP-21990BST | 16-bit fixed point DSP with Flash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2196MBST-140Z | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 140MHz 140MIPS 144-Pin LQFP |
| ADSP-2196MKST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 144-Pin LQFP 制造商:Analog Devices 功能描述:16-Bit DSP 160 MIPs 2.5V 40 Kbytes |
| ADSP-2196MKSTZ-160 | 功能描述:IC DSP CONTROLLER 16BIT 144-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-21990BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA 制造商:Rochester Electronics LLC 功能描述:160 MIPS, MIXED SIGNAL DSPWITH 14-BIT - Bulk |
| ADSP-21990BST | 制造商:Rochester Electronics LLC 功能描述:160 MIPS,MIXED SIGNAL DSP WITH 14BIT - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。