參數資料
型號： AD9983AKSTZ-1401
廠商： Analog Devices, Inc.
英文描述： High Performance 8-Bit Display Interface
中文描述： 高性能8位顯示接口
文件頁數： 17/44頁
文件大?。?/td> 470K
代理商： AD9983AKSTZ-1401
Preliminary Technical Data
AD9983A
Rev. PrA | Page 17 of 44
0
SOG INPUT
SOGOUT OUTPUT
CONNECTED TO
HSYNCIN
NEGATIVE PULSE WIDTH = 40 SAMPLE CLOCKS
COMPOSITE
SYNC
AT HSYNCIN
VSYNCOUT
FROM SYNC
SEPARATOR
–300mV
+300mV
0mV
700mV MAXIMUM
Figure 10. Sync Slicer and Sync Separator Output
Sync Separator
As part of sync processing, the sync separator’s task is to extract
Vsync from the composite sync signal. It works on the idea that
the Vsync signal stays active for a much longer time than the
Hsync signal. By using a digital low-pass filter and a digital
comparator, it rejects pulses with small durations (such as
Hsyncs and equalization pulses) and only passes pulses with
large durations, such as Vsync (see Figure 10).
The threshold of the digital comparator is programmable for
maximum flexibility. To program the threshold duration, write
a value (N) to Register 0x11. The resulting pulse width is N ×
200 ns. So, if N = 5, the digital comparator threshold is 1 μs.
Any pulse less than 1 μs is rejected, while any pulse greater than
1 μs passes through.
There are two factors to consider when using the sync separator.
First, the resulting clean Vsync output is delayed from the
original Vsync by a duration equal to the digital comparator
threshold (N × 200 ns). Second, there is some variability to the
200 ns multiplier value. The maximum variability over all
operating conditions is ±20% (160 ns to 240 ns). Since normal
Vsync and Hsync pulse widths differ by a factor of
approximately 500 or more, the 20% variability is not an issue.
Hsync Filter and Regenerator
The Hsync filter is used to eliminate any extraneous pulses from
the Hsync or SOGIN inputs, outputting a clean, low jitter signal
that is appropriate for mode detection and clock generation.
The Hsync regenerator is used to recreate a clean, although not
low jitter, Hsync signal that can be used for mode detection and
counting Hsyncs per Vsync. The Hsync regenerator has a high
degree of tolerance to extraneous and missing pulses on the
Hsync input, but is not appropriate for use by the PLL in
creating the pixel clock due to jitter.
The Hsync regenerator runs automatically and requires no
setup to operate. The Hsync filter requires the setting up of a
filter window. The filter window sets a periodic window of time
around the regenerated Hsync leading edge where valid Hsyncs
are allowed to occur. The general idea is that extraneous pulses
on the sync input occur outside of this filter window and thus
are filtered out. To set the filter window timing, program a value
(
x
) into Register 0x23. The resulting filter window time is ±
x
times 25 ns around the regenerated Hsync leading edge. Just as
for the sync separator threshold multiplier, allow a ±20%
variance in the 25 ns multiplier to account for all operating
conditions (20 ns to 30 ns range).
A second output from the Hsync filter is a status bit (Register 0x25,
Bit 1) that tells whether extraneous pulses were present on the
incoming sync signal or not. Often, extraneous pulses are
included for copy protection purposes, so this status bit can be
used to detect that.
The filtered Hsync (rather than the raw HSYNCx/SOGINx
signal) for pixel clock generation by the PLL is controlled by
Register 0x20, Bit 2. The regenerated Hsync (rather than the
raw Hsync/SOGIN signal) for the sync processing is controlled
by Register 0x20, Bit 1. Use of the filtered Hsync and
regenerated Hsync is recommended. See Figure 11 for an
illustration of a filtered Hsync.
相關PDF資料
PDF描述
AD9983AKSTZ-170 High Performance 8-Bit Display Interface
AD9983AKSTZ-1701 High Performance 8-Bit Display Interface
AD9983A High Performance 8-Bit Display Interface
AD9983AKCPZ-140 High Performance 8-Bit Display Interface
AD9983AKCPZ-1401 High Performance 8-Bit Display Interface
相關代理商/技術參數
參數描述
AD9983AKSTZ-170 功能描述:IC DISPLAY 8BIT 170MSPS 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9983AKSTZ-1701 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface
AD9983KSTZ-110 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9983KSTZ-140 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9983KSTZ-170 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*