- 您現在的位置：買賣IC網 > PDF目錄16826 > AD9956-VCO/PCBZ (Analog Devices Inc)BOARD EVAL 14BIT 1.8V 48LFCSP PDF資料下載
參數資料
| 型號： | AD9956-VCO/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL 14BIT 1.8V 48LFCSP |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 標準包裝： | 1 |
| 系列： | AgileRF™ |
| 主要目的： | 計時，直接數字合成（DDS） |
| 已用 IC / 零件： | AD9956 |
| 已供物品： | 板 |
| 相關產品： | AD9956YCPZ-ND - IC SYNTHESIZER 1.8V 48LFCSP AD9956YCPZ-REEL7-ND - IC SYNTHESIZER 1.8V 48LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9956
Rev. A | Page 30 of 32
CFR2<28:26> Clock Driver Falling Edge Control
These bits control the slew rate of the CML clock driver output’s
falling edge. When these bits are on, additional current is sent to
the output driver to increase the rising edge slew rate capability.
Table 7 describes how the bits increase the current; the contri-
butions of each bit are cumulative. Note that the additional cur-
rent is on only during the rising edge of the waveform, for ap-
proximately 250 ps, but not on during the entire transition.
Table 7. CML Clock Drive Falling Edge Slew Rate
Control Bits and Associated Surge Current
CFR2<28> = 1
5.4 mA
CFR2<30> = 1
2.7 mA
CFR2<29> = 1
1.35 mA
CFR2<25> PLL_LOCK_DETECT Enable
This bit enables the PLL_LOCK/SYNC_IN pin as a lock detect
output for the PLL.
CFR2<25> = 0 (default).The PLL_LOCK_DETECT signal is
disabled.
CFR2<25> = 1. The PLL_LOCK_DETECT signal is enabled.
CFR2<24> PLL_LOCK_DETECT Mode
This bit toggles the modes of the PLL_LOCK_DETECT func-
tion. The lock detect can either be a status indicator (locked or
unlocked), or it can indicate a lead-lag relationship between the
two phase frequency detector inputs.
CFR2<24> = 0 (default). The lock detect acts as a status indica-
tor (PLL is locked 0 or unlocked 1).
CFR2<24> = 1. The lock detect acts as a lead/lag indicator. A
1 on the PLL_LOCK pin means that the PLLOSC pin lags the
reference. A 0 means that the PLLOSC pin leads the reference.
CFR2<23> RF Divider Power-Down
This bit powers the RF divider down to save power when not in
used.
CFR2<23> = 0 (default). RF divider is on.
CFR2<23> = 1. RF divider is powered down and an alternate
path between the REFCLK inputs and SYSCLK is enabled.
CFR2<22:21> RF Divider Ratio
These two bits control the RF divider ratio (÷R).
CFR2<22:21> = 11 (default). RF Divider R = 8.
CFR2<22:21> = 10. RF Divider R= 4.
CFR2<22:21> = 01. RF Divider R = 2.
CFR2<22:21> = 00. RF Divider R = 1. Note that this is not the
same as bypassing the RF divider.
CFR2<20> Clock Driver Power-Down
This bit powers down the CML clock driver circuit.
CFR2<20> =1 (default). CML clock driver circuit is powered down.
CFR2<20> = 0. CML clock driver is powered up.
CFR2<19:18> Clock Driver Input Select
These bits control the mux on the input for the CML clock driver.
CFR2<19:18> = 00. The CML clock driver is disconnected from
all inputs (and does not toggle).
CFR2<19:18> = 01. The CML clock driver is driven by the
PLLOSC input pin.
CFR2<19:18> = 10 (default). The CML clock driver is driven by
the output of the RF divider.
CFR2<19:18> = 11. The CML clock driver is driven by the input
of the RF divider
CFR2<17> Slew Rate Control Bit
Even without the additional surge current supplied by the rising
edge slew rate control bits and the falling edge slew rate control
bits, the device applies a default 7.6 mA surge current to the
rising edge and a 4.05 mA surge current to the falling edge. This
bit disables all slew rate enhancement surge current, including
the default values.
CFR2<17> = 0 (default). The CML driver applies default surge
current to rising and falling edges.
CFR2<17> = 1. Driver applies no surge current during transi-
tions. The only current is the continuous current.
CFR2<16> RF Divider SYSCLK Mux Bit
This bit toggles the mux to control whether the RF divider out-
put or input is supplying SYSCLK to the device.
CFR2<16> = 0 (default). The RF divider output supplies the
DDS SYSCLK.
CFR2<16> = 1. The RF divider input supplies the DDS SYSCLK
(bypass the divider). Note that regardless of the condition of the
configuration of the clock input, the DDS SYSCLK must not
exceed the maximum rated clock speed.
相關PDF資料 |
PDF描述 |
|---|---|
| GEM22DRKF | CONN EDGECARD 44POS DIP .156 SLD |
| 362A024-4/86-0 | BOOT MOLDED |
| AD9956/PCBZ | BOARD EVAL FOR AD9956 |
| 0210391089 | CABLE JUMPER 1MM .203M 37POS |
| 570-003-744-200 | ASSEMBLY RECEPT 3POS WATERPROOF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9956XCPZ | 制造商:Analog Devices 功能描述:DGTL SYNTHESIZER 48LFCSP EP - Tape and Reel |
| AD9956YCP | 制造商:Analog Devices 功能描述:- Trays |
| AD9956YCPZ | 功能描述:IC SYNTHESIZER 1.8V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9956YCPZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 GHz DDS-Based AgileRF |
| AD9956YCPZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 GHz DDS-Based AgileRF |
發布緊急采購，3分鐘左右您將得到回復。