參數資料
型號: AD7813YNZ
廠商: Analog Devices Inc
文件頁數: 2/11頁
文件大?。?/td> 0K
描述: IC ADC 10BIT PARALLEL 16-DIP
標準包裝: 25
位數: 10
采樣率(每秒): 400k
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 17.5mW
電壓電源: 單電源
工作溫度: -40°C ~ 105°C
安裝類型: 通孔
封裝/外殼: 16-DIP(0.300",7.62mm)
供應商設備封裝: 16-PDIP
包裝: 管件
輸入數目和類型: 1 個單端,單極
AD7813
–10–
REV. C
MICROPROCESSOR INTERFACING
The parallel port on the AD7813 allows the device to be inter-
faced to a range of many different microcontrollers. This section
explains how to interface the AD7813 with some of the more
common microcontroller parallel interface protocols.
AD7813 to 8051
Figure 16 shows a parallel interface between the AD7813 and
the 8051 microcontroller. The BUSY signal on the AD7813 pro-
vides an interrupt request to the 8051 when a conversion begins.
Port 0 of the 8051 may serve as an input or output port, or as in
this case when used together, may be used as a bidirectional
low-order address and data bus. The address latch enable out-
put of the 8051 is used to latch the low byte of the address dur-
ing accesses to the device, while the high-order address byte is
supplied from Port 2. Port 2 latches remain stable when the
AD7813 is addressed, as they do not have to be turned around
(set to 1) for data input as is the case for Port 0.
AD7813*
8051*
AD0–AD7
ALE
A8–A15
RD
INT
LATCH
DECODER
DB0–DB7
CS
RD
BUSY
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 16. Interfacing to the 8051
AD7813 to PIC16C6x/7x
Figure 17 shows a parallel interface between the AD7813 and the
PIC16C64/65/74. The BUSY signal on the AD7813 provides
an interrupt request to the microcontroller when a conversion
begins. Of the PIC16C6x/7x range of microcontrollers only the
PIC16C64/65/74 can provide the option of a parallel slave port.
Port D of the microcontroller will operate as an 8-bit wide
parallel slave port when control bit PSPMODE in the TRISE
register is set. Setting PSPMODE enables the port pin RE0
to be the RD output and RE2 to be the CS output. For this
functionality, the corresponding data direction bits of the
TRISE register must be configured as outputs (reset to 0).
See PIC16/17 Microcontroller User Manual.
PIC16C6x/7x*
PSP0–PSP7
RD
INT
*ADDITIONAL PINS OMITTED FOR CLARITY
CS
AD7813*
DB0–DB7
CS
RD
BUSY
Figure 17. Interfacing to the PIC16C6x/7x
AD7813 to ADSP-21xx
Figure 18 shows a parallel interface between the AD7813 and
the ADSP-21xx series of DSPs. As before, the BUSY signal on
the AD7813 provides an interrupt request to the DSP when a
conversion begins.
*ADDITIONAL PINS OMITTED FOR CLARITY
ADDRESS
DECODE
LOGIC
EN
AD7813*
DB0–DB7
CS
RD
BUSY
ADSP-21xx*
D7–D0
DMS
A13–A0
RD
IRQ
Figure 18. Interfacing to the ADSP-21xx
相關PDF資料
PDF描述
AD7708BRZ-REEL7 IC ADC 16BIT R-R 8/10CH 28SOIC
CS3100A-14S-78P CONN RCPT 2POS WALL MNT W/PINS
AD7366BRUZ-5-RL7 IC ADC 12BIT DUAL BIPO 24-TSSOP
MS27467E21B11BA CONN HSG PLUG 11POS STRGHT SCKT
D38999/26MD19SNLC CONN HSG PLUG 19POS STRGHT SCKT
相關代理商/技術參數
參數描述
AD7813YR 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N 制造商:Analog Devices 功能描述:IC 10-BIT ADC
AD7813YR-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N T/R
AD7813YR-REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N T/R
AD7813YRU 功能描述:IC ADC 10BIT PARALLEL 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7813YRU-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 400KSPS 10-BIT PARALLEL 16TSSOP - Tape and Reel