參數資料
型號： 935270030157
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP48
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-313-2, LQFP-48
文件頁數： 16/53頁
文件大?。?/td> 704K
代理商： 935270030157
Philips Semiconductors
SC16C650A
Universal Asynchronous Receiver/Transmitter (UART)
with 32-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 03 — 13 March 2003
23 of 49
9397 750 11207
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by
writing the appropriate bits in this register.
[1]
When LCR[7] = 1, the general register set cannot be accessed until LCR[7] = 0.
Table 15:
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7] [1]
Divisor latch enable. The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled (normal default condition).
Logic 1 = Divisor latch and enhanced feature register enabled.
6
LCR[6]
Set break. When enabled, the Break control bit causes a break condition
to be transmitted (the TX output is forced to a logic 0 state). This
condition exists until disabled by setting LCR[6] to a logic 0.
Logic 0 = no TX break condition (normal default condition).
Logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the
remote receiver to a line break condition.
5
LCR[5]
Set parity. If the parity bit is enabled, LCR[5] selects the forced parity
format. Programs the parity conditions (see Table 16).
Logic 0 = parity is not forced (normal default condition).
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1
for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0
for the transmit and receive data.
4
LCR[4]
Even parity. If the parity bit is enabled with LCR[3] set to a logic 1,
LCR[4] selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd number of
logic 1s in the transmitted data. The receiver must be programmed to
check the same format (normal default condition).
Logic 1 = EVEN Parity is generated by forcing an even number of
logic 1s in the transmitted data. The receiver must be programmed to
check the same format.
3
LCR[3]
Parity enable. Parity or no parity can be selected via this bit.
Logic 0 = no parity (normal default condition).
Logic 1 = a parity bit is generated during the transmission, receiver
checks the data and parity for transmission errors.
2
LCR[2]
Stop bits. The length of stop bit is specied by this bit in conjunction with
the programmed word length (see Table 17).
Logic 0 or cleared = default condition.
1-0
LCR[1-0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see Table 18).
Logic 0 or cleared = default condition.
相關PDF資料
PDF描述
937-SP-3044-031 4 CONTACT(S), MALE, TELECOM AND DATACOM CONNECTOR, IDC, PLUG
937-SP-3088R-K1-031 8 CONTACT(S), MALE, TELECOM AND DATACOM CONNECTOR, IDC, PLUG
940-SP-3044-031 4 CONTACT(S), MALE, TELECOM AND DATACOM CONNECTOR, IDC, PLUG
940-SP-3088R-031 8 CONTACT(S), MALE, TELECOM AND DATACOM CONNECTOR, IDC, PLUG
940-SP-361010-K1-A108 10 CONTACT(S), MALE, TELECOM AND DATACOM CONNECTOR, IDC, PLUG
相關代理商/技術參數
參數描述
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
935270792551 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270792557 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270793551 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
935270793557 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*