TABLE
參數資料
型號： XRT86VL34IB
廠商： Exar Corporation
文件頁數： 44/155頁
文件大小： 0K
描述： IC LIU/FRAMER T1/E1/J1 4CH 225BG
標準包裝： 84
控制器類型： T1/E1/J1 調幀器，LIU
電源電壓： 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 225-BGA
供應商設備封裝： 225-BGA（19x19）
包裝： 托盤
XRT86VL34
133
QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
REV. V1.2.1
TABLE 111: LIU CHANNEL CONTROL INTERRUPT ENABLE REGISTER (LIUCCIER)
HEX ADDRESS: 0X0FN4
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
7
Reserved
RO
0
This Bit Is Not Used
6
DMOIE_n
R/W
0
Change of Transmit DMO (Drive Monitor Output) Condition Inter-
rupt Enable:
This bit permits the user to either enable or disable the “Change of
Transmit DMO Condition” Interrupt. If the user enables this interrupt,
then the XRT86VL34 device will generate an interrupt any time when
either one of the following events occur.
1. Whenever the Transmit Section toggles the DMO Status bit (Bit 6
or Register 0x0Fn5) to “1”.
2. Whenever the Transmit Section toggles the DMO Status bit (Bit 6
or Register 0x0Fn5) to “0”.
0 – Disables the “Change in the DMO Condition” Interrupt.
1 – Enables the “Change in the DMO Condition” Interrupt.
5
FLSIE_n
R/W
0
FIFO Limit Status Interrupt Enable:
This bit permits the user to either enable or disable the “FIFO Limit Sta-
tus” Interrupt. If the user enables this interrupt, then the XRT86VL34
device will generate an interrupt when the jitter attenuator Read/Write
FIFO pointers are within +/- 3 bits.
0 = Disables the “FIFO Limit Status” Interrupt
1 = Enables the “FIFO Limit Status” Interrupt
4
LCVIE_n
R/W
0
Line Code Violation Interrupt Enable:
This bit permits the user to either enable or disable the “Line Code Viola-
tion” Interrupt. If the user enables this interrupt, then the XRT86VL34
device will generate an interrupt when a LCV error or an excessive zero
condition is detected.
0 = Disables the “Line Code Violation” Interrupt
1 = Enables the “Line Code Violation” Interrupt
3
NLCDIE_n
R/W
0
Change in Network Loop-Code Detection Interrupt Enable:
This bit permits the user to either enable or disable the “Change in Net-
work Loop-Code Detection” Interrupt. If the user enables this interrupt,
then the XRT86VL34 device will generate an interrupt any time when
either one of the following events occur.
1. Whenever the Receive Section (within XRT86VL34) detects the
Network Loop-Code (Loop-Up or Loop-Down depending on which
Loop-Code the Receive LIU is configured to detect).
2. Whenever the Receive Section (within XRT86VL34) no longer
detects
the
Network
Loop-Code
(Loop-Up
or
Loop-Down
depending on which Loop-Code the Receive LIU is configured to
detect).
0 – Disables the “Change in Network Loop-Code Detection” Interrupt.
1 – Enables the “Change in Network Loop-Code Detection” Interrupt.
2
Reserved
-
This bit is not used
相關PDF資料
PDF描述
PIC24F08KL201T-I/MQ IC MCU 16BIT 8KB FLASH 20-QFN
XRT86VL32IB IC LIU/FRAMER T1/E1/J1 2CH 225BG
PIC16LF1933T-I/MV IC MCU 8BIT 7KB FLASH 28UQFN
V300A12C400B CONVERTER MOD DC/DC 12V 400W
V300A15C400BG3 CONVERTER MOD DC/DC 15V 400W
相關代理商/技術參數
參數描述
XRT86VL34IB-F 功能描述:網絡控制器與處理器 IC 4-Ch T1/E1/J1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL38_07 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
XRT86VL38_1 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VL38_2 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*