參數資料
型號： XRT75R03DIV
廠商： Exar Corporation
文件頁數： 85/135頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 3CH 128LQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 3/3
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x20）
包裝： 托盤
XRT75R03D
49
REV. 1.0.4
THREE CHANNEL E3/DS3/STS-1 LINE
6.4.3
Muting the Recovered Data with LOS condition:
When the LOS condition is declared, the clock recovery circuit locks into the reference clock applied to the
ExClk_n pin and output this clock on the RxClk_n output.In Single Frequency Mode (SFM), the clock recovery
locks into the rate clock generated and output this clock on the RxClk_n pins. The data on the RPOS_n and
RNEG_n pins can be forced to zero by pulling the LOSMUT pin “High” (in Hardware Mode) or by setting the
LOSMUT_n bits in the individual channel control register to “1” (in Host Mode).
NOTE: When the LOS condition is cleared, the recovered data is output on RPOS_n and RNEG_n pins.
7.0
JITTER:
There are three fundamental parameters that describe circuit performance relative to jitter:
Jitter Tolerance (Receiver)
Jitter Transfer (Receiver/Transmitter)
Jitter Generation
7.1
JITTER TOLERANCE - RECEIVER:
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 21, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence.
Input jitter tolerance requirements are specified in terms of compliance with jitter mask which is represented as
a combination of points.Each point corresponds to a minimum amplitude of sinusoidal jitter at a given jitter
frequency.
7.1.1
DS3/STS-1 Jitter Tolerance Requirements:
Bellcore GR-499 CORE, Issue 1, December 1995 specifies the minimum requirement of jitter tolerance for
Category I and Category II. The jitter tolerance requirement for Category II is the most stringent. Figure 22
shows the jitter tolerance curve as per GR-499 specification.
FIGURE 22. JITTER TOLERANCE MEASUREMENTS
FREQ
Synthesizer
Pattern
Generator
DUT
XRT75VL03D
Error
Detector
Modulation
Freq.
Data
Clock
相關PDF資料
PDF描述
ISL26710IHZ-T IC ADC 10BIT SPI/SRL 1M 8-SOT-23
MS27472T10F35SB CONN RCPT 13POS WALL MNT W/SCKT
IDT72V3656L15PF8 IC SYNC FIFO 4096X36 15NS 128QFP
IDT72V3654L15PF8 IC BI FIFO 4096X36 15NS 128QFP
MS27467T23A53P CONN PLUG 53POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
XRT75R03DIV-F 功能描述:網絡控制器與處理器 IC 3-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R03DIVTR 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIVTR-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT75R03ES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+JA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03IV 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*