參數資料
型號： XRT73LC04AIV
廠商： Exar Corporation
文件頁數： 7/64頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 4CH 144LQFP
標準包裝： 60
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
XRT73LC04A
.
11
REV. 1.0.2
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
111
LOSMUTEN
I
MUTE-upon-LOS Enable Input (Hardware Mode):
This input pin is use to configure the XRT73LC04A, while it is operating
in the Hardware Mode, to MUTE the recovered data via the RPOS_(n),
RNEG_(n) output pins whenever one of the Channels declares an LOS
conditions.
Setting this input pin “High" configures all Channels to automatically pull
the RPOS_(n) and RNEG_(n) output pins “Low” whenever it is declaring
an LOS condition, thereby MUTing the data being output to the Terminal
Equipment.
Setting this input pin "Low" configures all Channels to NOT automatically
MUTE the recovered data whenever an LOS condition is declared.
NOTES:
1. This pin is ignored and should be tied to GND if the
XRT73LC04A is going to be operating in the HOST Mode.
2. This pin is internally pulled "Low".
CONTROL AND ALARM INTERFACE
PIN #
NAME
TYPE
DESCRIPTION
MICROPROCESSOR INTERFACE
PIN #
NAME
TYPE
DESCRIPTION
69
CS/
SR/DR
I
Microprocessor Serial Interface - Chip Select Input/Encoder-
Decoder Disable Input:
The function of this pin depends upon whether the XRT73LC04A is oper-
ating in the HOST Mode or in the Hardware Mode.
HOST Mode Operation - Chip Select Input:
The Local Microprocessor must assert this pin to "0" in order to enable
communication with the XRT73LC04A via the Microprocessor Serial
Interface.
NOTE: This pin is internally pulled "High".
70
SClk/(RxOFF)
I
Microprocessor Serial Interface Clock Signal/Receiver Shut OFF
Input:
The function of this pin depends upon:
HOST Mode - Microprocessor Serial Interface Clock Signal:
This signal is used to sample the data on the SDI pin on the rising edge
of this signal. During Read operations the Microprocessor Serial Inter-
face updates the SDO output on the falling edge of this signal.
Hardware Mode - Receiver Shut OFF input:
Setting this input pin "High" shuts off all of the Receiver Sections. Set-
ting this input pin "Low" enables all of the Receive Sections for full oper-
ation.
71
SDI/E3_1
I
Serial Data Input for the Microprocessor Serial Interface
This pin has a dual function.
HOST Mode:
To read or write data into the Command Registers over the Microproces-
sor Serial Interface, apply the Read/Write bit, the Address Values of the
Command Registers and Data Value to be written during Write Opera-
tions to this pin.
This input is sampled on the rising edge of the SClk pin.
相關PDF資料
PDF描述
IDT72V3660L15PFI8 IC FIFO SS 4096X36 15NS 128-TQFP
MS27499E8B6SA CONN RCPT 6POS BOX MNT W/SCKT
XRT75L02IV-F IC LIU E3/DS3/STS-1 2CH 100TQFP
MS3101F22-12S CONN RCPT 5POS FREE HNG W/SCKT
M83723/75A14126 CONN PLUG 12POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
XRT73LC04AIV-F 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R06ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73R06IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R06IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*