- 您現在的位置：買賣IC網 > PDF目錄9995 > XRT73LC04AIV (Exar Corporation)IC LIU E3/DS3/STS-1 4CH 144LQFP PDF資料下載
參數資料
| 型號： | XRT73LC04AIV |
| 廠商： | Exar Corporation |
| 文件頁數： | 54/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| 標準包裝： | 60 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 4/4 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
XRT73LC04A
54
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.2
tion. This bit-field is set to "1" if the Channel(n) Digital
LOS Detector is currently declaring an LOS condition.
NOTE: The purpose is to isolate the Detector (e.g., either
the Analog LOS or the Digital LOS detector) that is declar-
ing the LOS condition. This feature may be useful for trou-
bleshooting/debugging purposes.
Bit D0 - DMO_(n) (Drive Monitor Output Status -
Channel(n))
This Read-Only bit-field reflects the status of the
DMO output pin.
5.2.2
Command Register CR1
The bit-format and default values for Command Reg-
ister CR1-(n) are listed below followed by the function
of each of these bit-fields..
Bit D4 - TxOFF_(n) (Transmitter OFF - Channel(n))
This Read/Write bit-field is used to turn off the Chan-
nel(n) Transmitter.
Writing a "1" to this bit field turns off the Transmitter
and tri-state the Transmit Output. Writing a "0" to this
bit-field turns on the Transmitter.
Bit D3 - TAOS_(n) (Transmit All OneS - Chan-
nel(n))
This Read/Write bit-field is used to command the
Channel(n) Transmitter to generate and transmit an
all “1’s” pattern onto the line.
Writing a "1" to this bit-field commands the Transmit-
ter to transmit an all “1’s” pattern onto the line. Writ-
ing a "0" to this bit-field commands normal operation.
Bit D2 - TxClkINV_(n) (Transmit Clock Invert -
Channel(n))
This Read/Write bit-field is used to configure the
Transmitter to sample the signal at the TPData and
TNData pins on the rising edge or falling edge of Tx-
Clk (the Transmit Line Clock signal).
Writing a "1" to this bit-field configures the Transmitter
to sample the TPData and TNData input pins on the
rising edge of TxClk. Writing a “0" to this bit-field con-
figures the Transmitter to sample the TPData and
TNData input pins on the falling edge of TxClk.
Bit D1 - TxLEV_(n) (Transmit Line Build-Out En-
able/Disable Select - Channel(n))
This Read/Write bit-field is used to enable or disable
the Channel(n) Transmit Line Build-Out circuit.
Setting this bit-field "High" disables the Channel(n)
Line Build-Out circuit. In this mode, Channel(n) out-
puts partially-shaped pulses onto the line via the
TTIP_(n) and TRing_(n) output pins.
Setting this bit-field "Low" enables the Channel(n)
Line Build-Out circuit. In this mode, Channel(n) out-
puts shaped pulses onto the line via the TTIP_(n) and
TRing_(n) output pins.
In order to comply with the Isolated DSX-3/STSX-1
Pulse Template Requiremnts per Bellcore GR-499-
CORE or GR-253-CORE:
a. Set this bit-field to "1" if the cable length between
the Cross-Connect and the transmit output of Chan-
nel(n) is greater than 225 feet.
b. Set this bit-field to "0" if the cable length between
the Cross-Connect and the transmit output of Chan-
nel(n) is less than 225 feet.
This bit-field is active only if the XRT73LC04A is con-
figured to operate in the DS3 or SONET STS-1
Modes.
If the cable length is greater than 225 feet, set this bit-
field to "1" in order to increase the amplitude of the
Transmit Output Signal. If the cable length is less
than 225 feet, set this bit-field to "0".
NOTE: This option is only available when the XRT73LC04A
is operating in the DS3 or STS-1 Mode.
5.2.3
Command Register CR2-(n)
The bit-format and default values for Command Reg-
ister CR2-(n) are listed below followed by the function
of each of these bit fields.
COMMAND REGISTER CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) Reserved
0
COMMAND REGISTER CR2-(n)
D4
D3
D2
D1
D0
Reserved
ALOSDIS_(n)
DLOSDIS_(n)
REQEN_(n)
X
0
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72V3660L15PFI8 | IC FIFO SS 4096X36 15NS 128-TQFP |
| MS27499E8B6SA | CONN RCPT 6POS BOX MNT W/SCKT |
| XRT75L02IV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| MS3101F22-12S | CONN RCPT 5POS FREE HNG W/SCKT |
| M83723/75A14126 | CONN PLUG 12POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC04AIV-F | 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73R06ES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73R06IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73R06IB-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。