- 您現在的位置：買賣IC網 > PDF目錄372950 > XRT73L00 (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73L00 |
| 廠商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | E3/DS3/STS-1線路接口單元 |
| 文件頁數： | 50/53頁 |
| 文件大?。?/td> | 604K |
| 代理商： | XRT73L00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁
XRT73L00
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.2.0
á
47
This Read/Write bit-field is used to configure the
XRT73L00 to operate in either the SONET STS-1
Mode or the DS3 Mode.
Writing a “0” into this bit-field configures the
XRT73L00 to operate in the DS3 Mode. Writing a “1”
into this bit-field configures the XRT73L00 to operate
in the SONET STS-1 Mode.
N
OTE
:
This bit-field is ignored if the E3 bit-field (D2 in this
Command Register) is set to “1”.
Bit D2 - E3 Mode Select
This Read/Write bit-field is used to configure the
XRT73L00 to operate in the E3 Mode.
Writing a “0” into this bit-field configures the
XRT73L00 to operate in either the DS3 or SONET
STS-1 Mode specified by the setting of the DS3 bit-
field in this Command Register. Writing a “1” into this
bit-field configures the XRT73L00 to operate in the E3
Mode.
Bit D1 - LLB (Local Loop-Back)
This Read/Write bit-field along with RLB (bit D0 in this
Command Register) is used to select which Loop-
Back mode the XRT73L00 operates in. Table 6 re-
lates the state of the LLB and RLB to the selected
Loop-Back mode.
Bit D0 - RLB (Remote Loop-Back)
This Read/Write bit-field along with LLB (bit D1 in this
Command Register) is used to select which Loop-
Back mode the XRT73L00 operate in. Table 6 relates
the state of the LLB and RLB bits to the selected
Loop-Back mode.
5.2
O
PERATING
THE
M
ICROPROCESSOR
S
ERIAL
I
NTERFACE
.
The XRT73L00 Serial Interface is a simple four wire
interface that is compatible with many of the micro-
controllers available in the market. This interface
consists of the following signals:
CS
-
Chip Select (Active Low)
SCLK
-
Serial Clock
SDI
-
Serial Data Input
SDO
-
Serial Data Output
Using the Microprocessor Serial Interface
The following instructions for using the Microproces-
sor Serial Interface are best understood by referring
to the diagram in Figure 33.
In order to use the Microprocessor Serial Interface, a
clock signal must be supplied to the SCLK input pin.
A Read or Write operation can then be initiated by as-
serting the active-low Chip Select input pin (CS). It is
important to assert the CS pin (e.g., toggle it “Low”) at
least 50ns prior to the very first rising edge of the
clock signal.
Once the CS input pin has been asserted, the type of
operation and the target register address must now
be specified. This information is supplied to the Mi-
croprocessor Serial Interface by writing eight serial
bits of data into the SDI input.
N
OTE
:
Each of these bits is clocked into the SDI input on
the rising edge of SCLK. These eight bits are identified and
described below.
Bit 1 - R/W (Read/Write) Bit
This bit is clocked into the SDI input on the first rising
edge of SCLK after CS has been asserted. This bit
indicates whether the current operation is a Read or
Write operation. A “1” in this bit specifies a Read op-
eration, a “0” in this bit specifies a Write operation.
Bits 2 through 5: The four (4) bit Address Values
(labeled A0, A1, A2 and A3)
The next four rising edges of the SCLK signal clock in
the 4-bit address value for this particular Read (or
Write) operation. The address selects the Command
Register in the XRT73L00 that the user is either read-
ing data from or writing data to. The address bits
must be supplied to the SDI input pin in ascending or-
der with the LSB (least significant bit) first.
Bits 6 and 7:
The next two bits, A4 and A5 must be set to “0” as
shown in Figure 33.
Bit 8:
The value of A6 is a “don’t care”.
T
ABLE
6: L
OOP
-B
ACK
M
ODES
LLB
(B
IT
D1)
RLB
(B
IT
D0)
L
OOP
-B
ACK
M
ODE
0
0
No Loop-Back Mode (Normal
Operation)
0
1
Remote Loop-Back Mode
1
0
Analog Loop-Back Mode
1
1
Digital Loop-Back Mode
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L00A | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AIV | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT75L03DIV | Telecomm/Datacomm |
| XRT75L00 | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L00IV | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XRT73L00AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINE INTERFACE|QFP|44PIN|PLASTIC |
| XRT73L02M | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。