- 您現在的位置：買賣IC網 > PDF目錄372950 > XRT73L00 (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73L00 |
| 廠商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | E3/DS3/STS-1線路接口單元 |
| 文件頁數： | 48/53頁 |
| 文件大?。?/td> | 604K |
| 代理商： | XRT73L00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁
XRT73L00
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.2.0
á
45
Bit D2 - ALOS (Analog Loss of Signal Status)
This Read-Only bit-field indicates whether or not the
Analog LOS Detector in the XRT73L00 is currently
declaring an LOS condition.
This bit-field is set to “0” if the Analog LOS Detector in
the XRT73L00 is NOT currently declaring an LOS
condition. Conversely, this bit-field is set to “1” if the
Analog LOS Detector is currently declaring an LOS
condition.
The purpose of this feature is to isolate either the An-
alog LOS or the Digital LOS detector that is declaring
the LOS condition. This feature may be useful for
troubleshooting/debugging purposes.
Bit D1 - DLOS (Digital Loss of Signal Status)
This Read-Only bit-field indicates whether or not the
Digital LOS Detector in the XRT73L00 is currently de-
claring an LOS condition.
This bit-field is set to “0” if the Digital LOS Detector in
the XRT73L00 is NOT currently declaring an LOS
condition. Conversely, this bit-field is set to “1” if the
Digital LOS Detector is currently declaring an LOS
condition.
N
OTE
:
The purpose of this feature is to isolate the Detector
(e.g., either the Analog LOS or the Digital LOS detector)
that is declaring the LOS condition. This feature may be
useful for troubleshooting/debugging purposes.
Bit D0 - DMO (Drive Monitor Output Status)
This Read-Only bit-field reflects the status of the
DMO output pin.
5.1.2
Command Register - CR1
Bit D4 - TXOFF (Transmitter OFF)
This Read/Write bit-field is used to turn off the Trans-
mitter in the XRT73L00.
Writing a “1” to this bit-field turns off the Transmitter
and tri-states the Transmit Output. Writing a “0” to
this bit-field turns on the Transmitter.
Bit D3 - TAOS (Transmit All OneS)
This Read/Write bit-field is used to command the
XRT73L00 Transmitter to generate and transmit an all
“1’s” pattern onto the line.
Writing a “1” to this bit-field commands the Transmit-
ter to transmit an all “1’s” pattern onto the line. Writ-
ing a “0” to this bit-field commands normal operation.
Bit D2 - TXCLKINV (Transmit Clock Invert)
This Read/Write bit-field is used to configure the
XRT73L00 Transmitter to sample the signal at the TP-
DATA and TNDATA pins on the rising or falling edge of
TCLK (the Transmit Line Clock signal).
Writing a “1” to this bit-field configures the Transmitter
to sample the TPDATA and TNDATA input pins on the
rising edge of TCLK. Writing a “0” to this bit-field con-
figures the Transmitter to sample the TPDATA and
TNDATA input pins on the falling edge of TCLK.
Bit D1 - TXLEV (Transmit Level Select)
This Read/Write bit-field is used to enable or disable
the XRT73L00 Transmit Line Build-Out circuit.
Setting this bit-field "High" disables the Line Build-Out
circuit of the XRT73L00. In this mode, the XRT73L00
outputs partially-shaped pulses onto the line via the
TTIP and TRING output pins. Setting this bit-field
"Low" enables the Line Build-Out circuit of the
XRT73L00. In this mode the XRT73L00 outputs
shaped pulses onto the line via the TTIP and TRING
output pins.
To comply with the Isolated DSX/STSX-1 Pulse Tem-
plate Requirements per Bellcore GR-499-CORE or
GR-253-CORE, either:
1.
set this input pin to "1" if the cable length between
the Cross-Connect and the transmit output of the
XRT73L00 is greater than 225 feet or
2.
set this input pin to "0" if the cable length between
the Cross-Connect and the transmit output of the
XRT73L00 is less than 225 feet.
N
OTE
:
This option is only available when the XRT73L00 is
operating in the DS3 or STS-1 Mode.
Bit D0 - TXBIN (Transmit Binary Data)
This Read/Write bit-field permits configuring of the
Transmitter in the XRT73L00 to accept an un-encod-
ed binary data stream via the TPDATA input and con-
verts this data into the appropriate bipolar signal to
the line.
Writing a “1” configures the Transmitter to accept a bi-
nary data stream via the TPDATA input.
N
OTE
:
The TNDATA input is ignored.
This form of data acceptance is sometimes referred
to as Single-Rail mode operation. The Transmitter
then encodes this data into the appropriate line code
(e.g., B3ZS or HDB3) prior to its transmission over
the line.
Writing a “0” configures the Transmitter to accept data
in a Dual-Rail manner (e.g., via both the TPDATA and
TNDATA inputs).
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L00A | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AIV | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT75L03DIV | Telecomm/Datacomm |
| XRT75L00 | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L00IV | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XRT73L00AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINE INTERFACE|QFP|44PIN|PLASTIC |
| XRT73L02M | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。