REV. 1.4.3 30 4.3 Receiver The receiver section contains an 8-bit Receive Shift Register (RSR) " />
參數資料
型號: XR17C158CV-0A-EVB
廠商: Exar Corporation
文件頁數: 24/67頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR17C158-A 144TQF
標準包裝: 1
系列: *
XR17C158
xr
5V PCI BUS OCTAL UART
REV. 1.4.3
30
4.3
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and Receive Holding Register (RHR). The
RSR uses the 16X or 8X clock for timing. It verifies and validates every bit on the incoming character in the
middle of each data bit. On the falling edge of a start or false start bit, an internal receiver counter starts
counting at the 16X or 8X clock rate. After 8 or 4 clocks the start bit period should be at the center of the start
bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in this
manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are
sampled and validated in this same manner to prevent false framing. If there were any error(s), they are
reported in the LSR register bits 1-4. Upon unloading the receive data byte from RHR, the receive FIFO pointer
is bumped and the error flags are immediately updated to reflect the status of the data byte in RHR register.
RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO
trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out function
when receive data does not reach the receive FIFO trigger level. This time-out delay is 4 word lengths as
defined by LCR[1:0] plus 12 bits time. The RHR interrupt is enabled by IER bit-0.
4.3.1
Receive Holding Register (RHR) - Read-Only
The receive holding register is an 8-bit register that holds a receive data byte from the receive shift register
(RSR). It provides the receive data interface to the host processor. The host reads the receive data byte on this
register whenever a data byte is transferred from the RSR. RHR also part of the receive FIFO of 64 bytes by
11-bit wide, 3 extra bits are for the error flags to be in LSR register. When the FIFO is enabled by FCR bit-0, it
acts as the first-out register of the FIFO as new data are put over the first-in register. The receive FIFO pointer
is bumped after the RHR register is read. Also, the error flags associated with the data byte are immediately
updated onto the line status register (LSR) bits 1-4.
FIGURE 11. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE
Transmit Data Shift Register
(TSR)
Transmit
Data Byte
THR Interrupt (ISR bit-1) falls
below Programmed Trigger
Level (TXTRG) and then
when becomes empty. FIFO
is Enabled by FCR bit-0=1
Transmit
FIFO
(64-Byte)
TXFIFO1
16X or 8X Clock
(8XMODE Register)
Auto CTS Flow Control (CTS# pin)
Auto Software Flow Control
Flow Control Characters
(Xoff1/2 and Xon1/2 Reg.
相關PDF資料
PDF描述
SK221M025ST CAP ALUM 220UF 25V 20% RADIAL
M3TTK-1436J IDC CABLE - MSD14K/MC14G/MSD14K
CDB42L51 BOARD EVAL FOR CS42L51 CODEC
GMM11DRKI CONN EDGECARD 22POS DIP .156 SLD
UPJ1J151MHD6TO CAP ALUM 150UF 63V 20% RADIAL
相關代理商/技術參數
參數描述
XR17C158CV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C158CVTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C158CVTR-F
XR17C158IV 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C158IV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C158IVTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17C158IVTR-F