- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16V698IQ100-F (Exar Corporation)IC UART FIFO 32B OCTAL 100QFP PDF資料下載
參數資料
| 型號： | XR16V698IQ100-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 27/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 32B OCTAL 100QFP |
| 標準包裝： | 66 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 32 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.25 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-QFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
XR16V698
33
REV. 1.0.3
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
IER[7]: CTS# Input Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
LOW to HIGH.
IER[6]: RTS# Output Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when RTS# pin makes a transition from
LOW to HIGH.
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
IER[4]: Reserved
IER[3]: Modem Status Interrupt Enable
The Modem Status Register interrupt is issued whenever any of the delta bits of the MSR register (bits 3:0) is
set.
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[2]: Receive Line Status Interrupt Enable
An Overrun error, Framing error, Parity error or detection of a Break character will result in an LSR interrupt.
The 698 will issue an LSR interrupt immediately after receiving a character with an error. It will again re-issue
the interrupt (if the first one has been cleared by reading the LSR register) when the character with the error is
on the top of the FIFO, meaning the next one to be read out of the FIFO.
For example, let’s consider an incoming data stream of 0x55, 0xAA, etc and that the character 0xAA has a
Parity error associated with it. Let’s assume that the character 0x55 has not been read out of the FIFO yet. The
698 will issue an interrupt as soon as the stop bit of the character 0xAA is received. The LSR register will have
only the FIFO error bit (bit-7) set and none of the other error bits (Bits 1,2,3 and 4) will be set, since the byte on
the top of the FIFO is 0x55 which does not have any errors associated with it. When this byte has been read
out, the 698 will issue another LSR interrupt and this time the LSR register will show the Parity bit (bit-2) set.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[1]: TX Ready Interrupt Enable
In non-FIFO mode, a TX interrupt is issued whenever the THR is empty. In the FIFO mode, an interrupt is
issued twice: once when the number of bytes in the TX FIFO falls below the programmed trigger level and
again when the TX FIFO becomes empty. When auto RS-485 mode is enabled (FCTR bit-5 = 1), the second
interrupt is delayed until the transmitter (both the TX FIFO and the TX Shift Register) is empty.
Logic 0 = Disable Transmit Ready Interrupt (default).
Logic 1 = Enable Transmit Ready Interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16V794IV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V798IQ-F | IC UART FIFO 64B OCTAL 100QFP |
| XR17C152IM-F | IC UART PCI BUS DUAL 100TQFP |
| XR17C154IV | IC UART PCI BUS QUAD 144LQFP |
| XR17C158IV-F | IC UART PCI BUS OCTAL 144LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V698IQ100TR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 32Byte FIFO 2.5V/3.3V 100-Pin PQFP T/R 制造商:Exar Corporation 功能描述:XR16V698IQ100TR-F |
| XR16V794 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V QUAD UART WITH FRACTIONAL |
| XR16V794_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V QUAD UART WITH FRACTIONAL |
| XR16V794IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.25V TO 3.6V QUAD UART WITH FRACTIONAL |
| XR16V794IV-0A-EVB | 功能描述:UART 接口集成電路 Supports V794 64 ld TQFP,ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。