參數資料
型號： XCF16PVOG48C
廠商： XILINX INC
元件分類： DRAM
英文描述： Platform Flash In-System Programmable Configuration PROMS
中文描述： 16M X 1 CONFIGURATION MEMORY, PDSO48
封裝： LEAD-FREE, PLASTIC, TSOP-48
文件頁數： 11/46頁
文件大?。?/td> 525K
代理商： XCF16PVOG48C
Platform Flash In-System Programmable Configuration PROMS
DS123 (v2.9) May 09, 2006
www.xilinx.com
11
R
at a slow default frequency. The FPGA’s bitstream contains
configuration bits which can switch CCLK to a higher
frequency for the remainder of the Master Serial
configuration sequence. The desired CCLK frequency is
selected during bitstream generation.
Connecting the FPGA device to the configuration PROM for
Master Serial Configuration Mode (
Figure 6, page 14
):
The DATA output of the PROM(s) drive the DIN input of
the lead FPGA device.
The Master FPGA CCLK output drives the CLK input(s)
of the PROM(s)
The CEO output of a PROM drives the CE input of the
next PROM in a daisy chain (if any).
The OE/RESET pins of all PROMs are connected to
the INIT_B pins of all FPGA devices. This connection
assures that the PROM address counter is reset before
the start of any (re)configuration.
The PROM CE input can be driven from the DONE pin.
The CE input of the first (or only) PROM can be driven
by the DONE output of all target FPGA devices,
provided that DONE is not permanently grounded. CE
can also be permanently tied Low, but this keeps the
DATA output active and causes an unnecessary I
CC
active supply current (
"DC Characteristics Over
Operating Conditions," page 26
).
The PROM CF pin is typically connected to the FPGA's
PROG_B (or PROGRAM) input. For the XCFxxP only,
the CF pin is a bidirectional pin. If the XCFxxP CF pin is
not connected to the FPGA's PROG_B (or PROGRAM)
input, then the pin should be tied High.
FPGA Slave Serial Mode
In Slave Serial mode, the FPGA loads the configuration
bitstream in bit-serial form from external memory
synchronized by an externally supplied clock. Upon
power-up or reconfiguration, the FPGA's mode select pins
are used to select the Slave Serial configuration mode.
Slave Serial Mode provides a simple configuration interface.
Only a serial data line, a clock line, and two control lines
(INIT and DONE) are required to configure an FPGA. Data
from the PROM is read out sequentially on a single data line
(DIN), accessed via the PROM's internal address counter
which is incremented on every valid rising edge of CCLK.
The serial bitstream data must be set up at the FPGA’s DIN
input pin a short time before each rising edge of the
externally provided CCLK.
Connecting the FPGA device to the configuration PROM for
Slave Serial Configuration Mode (
Figure 7, page 15
):
The DATA output of the PROM(s) drive the DIN input of
the lead FPGA device.
The PROM CLKOUT (for XCFxxP only) or an external
clock source drives the FPGA's CCLK input.
The CEO output of a PROM drives the CE input of the
next PROM in a daisy chain (if any).
The OE/RESET pins of all PROMs are connected to
the INIT_B (or INIT) pins of all FPGA devices. This
connection assures that the PROM address counter is
reset before the start of any (re)configuration.
The PROM CE input can be driven from the DONE pin.
The CE input of the first (or only) PROM can be driven
by the DONE output of all target FPGA devices,
provided that DONE is not permanently grounded. CE
can also be permanently tied Low, but this keeps the
DATA output active and causes an unnecessary I
CC
active supply current (
"DC Characteristics Over
Operating Conditions," page 26
).
The PROM CF pin is typically connected to the FPGA's
PROG_B (or PROGRAM) input. For the XCFxxP only,
the CF pin is a bidirectional pin. If the XCFxxP CF pin is
not connected to the FPGA's PROG_B (or PROGRAM)
input, then the pin should be tied High.
Serial Daisy Chain
Multiple FPGAs can be daisy-chained for serial
configuration from a single source. After a particular FPGA
has been configured, the data for the next device is routed
internally to the FPGA’s DOUT pin. Typically the data on the
DOUT pin changes on the falling edge of CCLK, although
for some devices the DOUT pin changes on the rising edge
of CCLK. Consult the respective device data sheets for
detailed information on a particular FPGA device. For
clocking the daisy-chained configuration, either the first
FPGA in the chain can be set to Master Serial, generating
the CCLK, with the remaining devices set to Slave Serial
(
Figure 8, page 16
), or all the FPGA devices can be set to
Slave Serial and an externally generated clock can be used
to drive the FPGA's configuration interface (
Figure 7,
page 15
or
Figure 12, page 20
).
FPGA Master SelectMAP (Parallel) Mode
(XCFxxP PROM Only)
In Master SelectMAP mode, byte-wide data is written into
the FPGA, typically with a BUSY flag controlling the flow of
data, synchronized by the configuration clock (CCLK)
generated by the FPGA. Upon power-up or reconfiguration,
the FPGA's mode select pins are used to select the Master
SelectMAP configuration mode. The configuration interface
typically requires a parallel data bus, a clock line, and two
control lines (INIT and DONE). In addition, the FPGA’s Chip
Select, Write, and BUSY pins must be correctly controlled to
enable SelectMAP configuration. The configuration data is
read from the PROM byte by byte on pins [D0..D7],
accessed via the PROM's internal address counter which is
incremented on every valid rising edge of CCLK. The
bitstream data must be set up at the FPGA’s [D0..D7] input
pins a short time before each rising edge of the FPGA's
相關PDF資料
PDF描述
XCF32P Platform Flash In-System Programmable Configuration PROMS
XCF32PF48 Platform Flash In-System Programmable Configuration PROMS
XCF32PFG48 Platform Flash In-System Programmable Configuration PROMS
XCF32PFS48C Platform Flash In-System Programmable Configuration PROMS
XCF32PFSG48C Platform Flash In-System Programmable Configuration PROMS
相關代理商/技術參數
參數描述
XCF16PVOG48C0936 制造商:Xilinx 功能描述:XLXXCF16PVOG48C0936 PROM
XCF16PVOG48C4118 制造商:Xilinx 功能描述:
XCF3 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / XCF3
XCF32P 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMs
XCF32PF48 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*