參數資料
型號： X88C75LM
英文描述： Port Expander and E2 Memory
中文描述： 端口擴展和E2內存
文件頁數： 9/27頁
文件大?。?/td> 125K
代理商： X88C75LM
X88C75 SLIC
E
2
9
Interrupt Status Register (ISR)
The Interrupt Status Register is a volatile register used
to configure the interrupt condition for the I/O ports as
well as to determine the interrupt status of the ports. The
X88C75 ports can generate an interrupt to the microcon-
troller upon the proper transition (as specified in the
configuration register) on either STRA or STRB pins
when the corresponding I/O port is configured as an
input.
The INT flag is set when any of the input strobes are
toggled provided that their corresponding interrupt en-
able bits (ENA, ENB) are set. The INT flag is cleared
when latched data is read (PDR) or pending interrupt
status flag (INTA, INTB) in ISR is forced to “0” by the
interrupt service routine. Interrupt service routine should
examine the interrupt status flags (INTA, INTB) and
identify the source of pending interrupt.
The E
2
memory interrupt status flag (EOW) is another
means to detect the early completion of a write cycle.
When ENEE is enabled, the hardware will set the EOW
flag, and interrupt the microcontroller at the end of an
internal programming cycle. Toggle Bit Polling can be
replaced by this hardware interrupt, which reduces the
software overhead. The EOW flag should be cleared by
software. The interrupt status register bits are mapped
as follows.
Figure 10. Interrupt Status Register
INT
2887 ILL F14.1
INTA INTB
ENA
ENB ENEE
0
EOW
7
6
5
4
3
2
1
0
Interrupt Flag
“0” = No pending interrupt
“1” = Interrupt request
Port B – Interrupt Status
“0” = No pending interrupt
“1” = Port B latched data when a valid
transition occurred on the STRB
and port B was an input port.
Port A – Interrupt Enable
“0” = Mask off interrupt
“1” = Interrupt enabled
Port B – Interrupt Enable
“0” = Mask off interrupt
“1” = Interrupt enabled
EEPROM Interrupt Enable
“0” = Mask off interrupt
“1” = Interrupt enabled
EEPROM Interrupt Status
“0” = Programming in progress
“1” = Set by hardware when it completes
programming the previously
written data
Port A – Interrupt Status
“0” = No pending interrupt
“1” = Port A latched data when a valid
transition occurred on the STRA
and port A was an input port.
相關PDF資料
PDF描述
X88C75P Port Expander and E2 Memory
X88C75PI Port Expander and E2 Memory
X88C75PM Port Expander and E2 Memory
X9102P Digital Potentiometer
X9102PI Digital Potentiometer
相關代理商/技術參數
參數描述
X88C75P 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory
X88C75PI 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory
X88C75PM 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory
X8934 功能描述:固態繼電器-工業安裝 0381 SLD. R RELAY RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel
X8989-34 制造商:Cooper Crouse-Hinds 功能描述: 制造商:CROUSE-HINDS/COOPER 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*