- 您現在的位置：買賣IC網 > PDF目錄371276 > X88C75LM Port Expander and E2 Memory PDF資料下載
參數資料
| 型號： | X88C75LM |
| 英文描述： | Port Expander and E2 Memory |
| 中文描述： | 端口擴展和E2內存 |
| 文件頁數： | 11/27頁 |
| 文件大?。?/td> | 125K |
| 代理商： | X88C75LM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
X88C75 SLIC
E
2
11
PRINCIPLES OF OPERATION
I/O Port Operation
The expansion ports are accessible to the software
using their assigned memory mapped addresses. Each
port occupies two addresses in the SFR plane, the Port
Data Register and Port Pin Register. These registers
and their location in the 1K-byte register memory space
is shown on page 7.
The ports can be configured as either inputs or outputs,
the DIRA and DIRB bits in the configuration register are
used to select between the modes. The input signal on
the strobe pin, when the corresponding port is config-
ured as an input, is fed to the clock input of the port latch.
These are transparent latches and the trailing edge of
the strobe pulse is used to latch the data present on the
input pins. The strobe signal polarity is configurable
using the STPA and STPB bits in the configuration
register.
Writing to the port data register of an output port will
generate a pulse of fixed duration on its strobe pin. The
data also simultaneously arrives at the port output pins.
The latched data stays there until new data is written to
the port data register. The strobe pulse shape is con-
trolled by the state of the STPA and STPB bits in the
configuration register. A “1” forces the valid transition on
the corresponding strobe pin as active HIGH (
and a “0” sets it to active LOW (
),
).
When an external strobe signal is applied to an input
port, the latching of input data is followed by the setting
of the interrupt flags. The INTA and INTB interrupt flags
are used by ports A and B respectively, and are set along
with the INT interrupt flag at the end of strobe pulse input.
External interrupt (
IRQ
) is generated if the interrupt
enable flags (ENA and ENB) are set by the software.
The former enables the port A interrupt and the latter
enables the port B interrupt.
The port output drivers can be either CMOS or open-
drain. The wire-OR bits (AWO, BWO) in the configura-
tion register are used to make the selection. When the
bits are “0” the CMOS drivers are enabled. Setting these
bits will enable the open-drain output drivers. Small pull-
up resistors should be used on the pins of open-drain
ports.
INTERNAL DATA BUS
I/O
PIN
PORT
OUTPUT
OUTPUT
INPUT
LATCH FOR
I/O PIN
PORT WRITE
(PORT OUTPUT)
STROBE (PORT INPUT)
2887 ILL F16.1
PORT READ
(PORT INPUT)
PIN READ
(PORT IN OR OUTPUT)
Figure 12. Block Diagram of the I/O Ports
相關PDF資料 |
PDF描述 |
|---|---|
| X88C75P | Port Expander and E2 Memory |
| X88C75PI | Port Expander and E2 Memory |
| X88C75PM | Port Expander and E2 Memory |
| X9102P | Digital Potentiometer |
| X9102PI | Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X88C75P | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X88C75PI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X88C75PM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X8934 | 功能描述:固態繼電器-工業安裝 0381 SLD. R RELAY RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| X8989-34 | 制造商:Cooper Crouse-Hinds 功能描述: 制造商:CROUSE-HINDS/COOPER 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。