- 您現在的位置：買賣IC網 > PDF目錄231491 > W3E232M16S-266STIG (WHITE ELECTRONIC DESIGNS CORP) 64M X 16 DDR DRAM, 0.7 ns, PDSO66 PDF資料下載
參數資料
| 型號： | W3E232M16S-266STIG |
| 廠商： | WHITE ELECTRONIC DESIGNS CORP |
| 元件分類： | DRAM |
| 英文描述： | 64M X 16 DDR DRAM, 0.7 ns, PDSO66 |
| 封裝： | 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66 |
| 文件頁數： | 20/22頁 |
| 文件大?。?/td> | 0K |
| 代理商： | W3E232M16S-266STIG |
W3E232M16S-XSTX
7
White Electronic Designs Corporation (602) 437-1520 www.wedc.com
White Electronic Designs
December 2005
Rev. 1
White Electronic Designs Corp. reserves the right to change products or specications without notice.
PRELIMINARY*
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform
a NOP to the selected DDR SDRAM (CS# is LOW while
RAS#, CAS#, and WE# are high). This prevents unwanted
commands from being registered during idle or wait states.
Operations already in progress are not affected.
LOAD MODE REGISTER
The Mode Registers are loaded via inputs A0-12. The
LOAD MODE REGISTER command can only be issued
when all banks are idle, and a subsequent executable
command cannot be issued until tMRD is met.
ACTIVE
The ACTIVE command is used to open (or activate) a
row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and
the address provided on inputs A0-12 selects the row.
This row remains active (or open) for accesses until
a PRECHARGE command is issued to that bank. A
PRECHARGE command must be issued before opening
a different row in the same bank.
READ
The READ command is used to initiate a burst read access
to an active row. The value on the BA0, BA1 inputs selects
the bank, and the address provided on inputs A0-9 selects
the starting column location. The value on input A10
determines whether or not AUTO PRECHARGE is used. If
AUTO PRECHARGE is selected, the row being accessed
will be precharged at the end of the READ burst; if AUTO
PRECHARGE is not selected, the row will remain open
for subsequent accesses
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1 inputs
will be precharged at the end of the READ burst; if AUTO
PRECHARGE is not selected, the row will remain open
for subsequent accesses
PRECHARGE
The PRECHARGE command is used to deactivate the
open row in a particular bank or the open row in all banks.
The bank(s) will be available for a subsequent row access
a specied time (tRP) after the PRECHARGE command is
issued. Except in the case of concurrent auto precharge,
where a READ or WRITE command to a different bank is
allowed as long as it does not interrupt the data transfer
in the current bank and does not violate any other timing
parameters. Input A10 determines whether one or all
banks are to be precharged, and in the case where only
one bank is to be precharged, inputs BA0, BA1 select the
bank. Otherwise BA0, BA1 are treated as “Don’t Care.”
Once a bank has been precharged, it is in the idle state and
must be activated prior to any READ or WRITE commands
being issued to that bank. A PRECHARGE command will
be treated as a NOP if there is no open row in that bank
(idle state), or if the previously open row is already in the
FIGURE 3 – MODE REGISTER DEFINITION
M3 = 0
2
4
8
Reserved
M3 = 1
2
4
8
Reserved
Operating Mode
Normal Operation
Normal Operation/Reset DLL
All other states reserved
00
Valid
0
1
Burst Type
Sequential
Interleaved
CAS Latency
Reserved
2
Reserved
2.5
Reserved
Burst Length
M0
0
1
0
1
0
1
0
1
Burst Length
CAS Latency
BT
A9
A7
A6
A5
A4
A3
A8
A2
A1
A0
Mode Register (Mx)
Address Bus
M1
0
1
0
1
M2
0
1
M3
M4
0
1
0
1
0
1
0
1
M5
0
1
0
1
M6
0
1
M6-M0
M8
M7
Operating Mode
A10
A11
* M14 and M13
(BA0 and BA1 must be
"0, 0" to select
the base mode register
(vs. the extended
mode register).
0*
BA0
BA1
Reserved
M9
M10
M11
0
10
0
--
-
A12
M12
0
-
14
13
12 11 10
9
8
7
6
5
4
3
2
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| WPS256K16T-20LJC | 256K X 16 STANDARD SRAM, 20 ns, PDSO44 |
| WMF256K8-70FEM5A | 256K X 8 FLASH 5V PROM, 70 ns, CDFP32 |
| WMS512K8BV-20DEMEA | 512K X 8 STANDARD SRAM, 20 ns, CDSO32 |
| WS512K32-100HQE | 2M X 8 MULTI DEVICE SRAM MODULE, 100 ns, CHMA66 |
| WS512K32-85G2CE | 2M X 8 MULTI DEVICE SRAM MODULE, 85 ns, CQMA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W3E232M16S-400STC | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:2x32Mx16bit DDR SDRAM |
| W3E232M16S-400STCG | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:2x32Mx16bit DDR SDRAM |
| W3E232M16S-400STI | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:2x32Mx16bit DDR SDRAM |
| W3E232M16S-400STIG | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:2x32Mx16bit DDR SDRAM |
| W3E232M16S-XSTX | 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:2x32Mx16bit DDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。