參數資料
型號: W19B320STB9F
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
封裝: TFBGA-48
文件頁數: 51/52頁
文件大小: 1869K
代理商: W19B320STB9F
W19B(L)320ST/B
- 8 -
6.1.7 Output Disable Mode
When the #OE input is at VIH, output from the device is disabled. The output pins are set in the high
impedance state.
6.1.8 Autoselect Mode
The autoselect mode offers manufacturer and device identification, as well as sector protection
verification, through identifier codes output on DQ0
DQ7. This mode is primarily intended for
programming equipment to automatically match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes can also be accessed in-system through the
command register.
When using programming equipment, the autoselect mode requires VID (8.5 V to 12.5 V) on address
pins A9. Address pins A6, A1, and A0 must be as shown in table. In addition, when verifying sector
protection, the sector address must appear on the appropriate highest order address bits. When all
necessary bits have been set as required, the programming equipment may then read the
corresponding identifier code on DQ0
DQ7.
To access the autoselect codes in-system, the host system can issue the autoselect command
through the command register. This method does not require VID. Also refer to the Autoselect
Command Sequence section for more information.
6.1.9 Sector/Sector Block Protection and Unprotection
The hardware sector protection feature disables both program and erase operations in any sectors.
The hardware sector unprotection feature re-enables both program and erase operations in previously
protected sectors. Sector protection/unprotection can be implemented through two methods.
The primary method requires VID on the #RESET pin, and can be implemented either in-system or through
programming equipment. This method uses standard microprocessor bus cycle timing.
The alternate method intended only for programming equipment requires VID on address pin A9 and #OE It
is possible to determine whether a sector is protected or unprotected. See the Autoselect Mode section for
details.
6.1.10 Write Protect (#WP)
The Write Protect function provides a hardware method to protect the certain boot sectors without
using VID. This function is one of two features provided by the #WP/ACC pin.
When the #WP/ACC pin is set at VIL, the device disables program and erase functions in the two
outermost 8 Kbyte boot sectors independently of whether those sectors were protected or unprotected
using the method described in “Sector/Sector Block Protection and Unprotection.” The two outermost
8 Kbyte boot sectors are the two sectors containing either the lowest addresses in a bottom-boot-
configured device or the highest addresses in a top-boot-configured device.
When the #WP/ACC pin is set at VIH, the device reverts to the two outermost 8K Byte boot sectors
were last set either to be protected or unprotected. That is, sector protection or unprotection for these
two sectors depends on whether they were last protected or unprotected using the method described
in “Sector/Sector Block Protection and Unprotection”.
Please note that the #WP/ACC pin must not be left floating or unconnected; otherwise, the
inconsistent behavior of the device may occur.
相關PDF資料
PDF描述
WED3DG7266V7D1I-MG 64M X 72 SYNCHRONOUS DRAM MODULE, ZMA144
WEDPN16M64V-133B2M 16M X 64 SYNCHRONOUS DRAM, 5.5 ns, PBGA219
W25X32-VSSI-Z 32M X 1 FLASH 2.7V PROM, PDSO8
WF1024K32E-150H2M 4M X 8 FLASH 12V PROM MODULE, 150 ns, CHIP66
WS128K48-20G4WMA 768K X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQFP116
相關代理商/技術參數
參數描述
W19L-E02050 制造商:Cooper Crouse-Hinds 功能描述:
W19L-E03040 制造商:Cooper Crouse-Hinds 功能描述:
W19L-E04040 制造商:Cooper Crouse-Hinds 功能描述:
W19U_5LGA WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
W1A 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 類別:盒,外殼,支架 >> 箱 系列:工具 產品目錄繪圖:SR Series Standard 特色產品:Customize Your Enclosure 標準包裝:1 系列:S 容器 - 類型:盒 尺寸/尺寸:3.600" L x 2.250" W(91.44mm x 57.15mm) 高度:1.500"(38.10mm) 面積 (L x W):8.10"(52.3cm) 設計:手持,分叉式雙側 材質:塑料 - ABS 顏色:杏黃 厚度:0.100"(2.54mm) 特點:PCB 支座 額定值:IP40,NEMA 1 材料可燃性額定值:UL94 HB 裝運信息:從 Digi-Key 運送 重量:0.137 磅(62.14g) 相關產品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名稱:111-I ALMOND111-IA111-IALMONDSR111-IA